Firefly Open Source Community

Title: MMC Error [Print This Page]

Author: fieldtestARM Time: 1/25/2017 03:07
Title: MMC Error
Hi

i am currently booting a new firefly board from an SDCard containing a Debian image and I keep getting these errors when i am logged in over minicom:

mmcblk0: error -110 sending status command, retrying
mmcblk0: error -115 sending stop command, original cmd response 0x900, card status 0x900
mmcblk0: error -84 transferring data, sector 1097784, nr 256, cmd response 0x900, card status 0x0
mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
mmcblk0: error -84 transferring data, sector 219840, nr 8, cmd response 0x900, card status 0xb00
mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)

While the board is operational I would like to understand if there is any issue.

On an older Firefly RK3288 board I do not see any issues with the same image.

Any ideas ?

Thanks
A

Author: isle Time: 2/5/2017 09:27
Hi
the older firefly RK3288 board , you mean the public test development board (0809) ?

Author: fieldtestARM Time: 2/7/2017 19:17
By older I mean a board we ordered about a year ago. The older board has a brown base board but the new one was ordered a couple of weeks ago and has a black base boards.

Thanks
A

Author: isle Time: 2/8/2017 09:43

hi could you take a picture with the older and the newer board like this ?

Author: fieldtestARM Time: 2/13/2017 18:35
Last edited by fieldtestARM In 2/13/2017 18:37 Editor

Hi

Thanks for your reply. Hope the photos are okay.

The old board date read 2014.09.30
The new board date reads 2016.06.23

Thanks
A

Old.jpg (1.74 MB, Down times: 184)

New.jpg (2.03 MB, Down times: 176)

Author: isle Time: 2/14/2017 15:22
Hi
these two boards have very little changes,so it shouldn't show different results with the same image,
Can you use the SDcard when the system is ready?(android or ubuntu )
please make sure the hardware is ok.

Author: fieldtestARM Time: 2/14/2017 18:17
I can use the SD Card on Ubunut but not without seeing the error i described above consistently on the serial port.

I also see some Bus Errors when trying to do any file accesses.

Regards
A

Author: isle Time: 2/15/2017 14:21
Hi
I have tried boot a ubuntu image from SDCard with the hardware version "20160623" like yours, But I haven't get any error log of mmcblk0 like yours .
So,about your debian image, did you make it by yourself? which kernel did you use?

Author: fieldtestARM Time: 2/17/2017 22:01
Kernel version is 4.1.0 and its the same used across both boards. Also trying it on a board with a date 2016-11-16 seems to work

The ones labeled 2016.06.23 seem to have an issue

A

Author: isle Time: 2/18/2017 09:25
Hi
how many boards labeled 2016.06.23 do you have?
All of them have the issue?

Author: fieldtestARM Time: 2/21/2017 02:17
Hi

We have 5 labelled 2016.06.23 and they all show the same problems

All other firefly boards with a different date work fine.

A

Author: isle Time: 2/24/2017 09:58
Hi
Could you send your firmware (with SDCard boot) to me,and I will check whether it is have the same issue on my board.

Welcome Firefly Open Source Community (https://bbs.t-firefly.com/)