Firefly Open Source Community

Title: Bord can't enter Loader Mode [Print This Page]

Author: pacopad Time: 12/13/2014 18:20
Title: Bord can't enter Loader Mode

Hi , after flashing an android omg my board wand get in loader mode

here is the debug output

U-Boot 2014.10-RK3288-02 (Oct 30 2014 - 09:27:41)

CPU: rk3288

CPU's clock information:

arm pll = 600000000HZ

periph pll = 300000000HZ

ddr pll = 200000000HZ

codec pll = 594000000HZ

Board: Rockchip platform Board

DRAM: Found dram banks:1

Adding bank:0000000000000000(0000000080000000)

128 MiB

storage init OK!

Using default environment

GetParam

check parameter success

Unknow param: MACHINE_MODEL:rk30sdk!

Unknow param: MACHINE_ID:007!

Unknow param: MANUFACTURER:RK30SDK!

Unknow param: PWR_HLD: 0,0,A,0,1!

failed to prepare fdt from boot!

power key: bank-0 pin-5

can't find dts node for act8846

can't find dts node for rk808

can't find dts node for rk818

Can't find dts node for fuel guage cw201x

SecureBootEn = 0, SecureBootLock = 0

#Boot ver: 2014-10-30#2.17

sn:100612000100004E

no fuel gauge found

read logo_on switch from dts [1]

pll_src = 0, dclk_hz = 205000000, dclk_div = 2

edp pll locked

Aux Transaction fail!

hw lt err:1

link train failed!

unable to config video

checkKey

vbus = 1

rockusb key pressed.

When i let it boot normally It's detected as MSC mode in rkandroidtool but when i select "switch" i got nearly the same result.

What can i do ?

best regards

Pacopad

Author: pacopad Time: 12/13/2014 22:36

I solved my problem ,

i burned a linux image on SDCard and i formated the flash.

Then i can flash it normal again

Pacopad

Author: busybee Time: 12/15/2014 14:38

Hello,??pacopad, would you please share your story a little bit more in detail?

This is a good reference of a new way for system recovery.

Author: zhansb Time: 12/17/2014 10:10

I think use "EraseFlash" can fix this problem

Author: pacopad Time: 12/17/2014 20:29

Here is the story. I flashed an Android image from a TV Box (i dont remember which one).

When the Android started , the board was detected as MSC device so i could do nothing with AndroidTool. When i tried to select "SWITCH" on Android tool or boot in Loader Mode , the board was n't recognized on my computer. Nothing in USB Logs.

So i burned a linux distro for rk3288 on a SD Card and i formatted the flash with gparted.

After that the board was recognized in Loader Mode with AndroidTool

Best regards

Pacopad

Author: busybee Time: 12/19/2014 10:30

Hi Pacopad, how do you burn a Linux distro for rk3288 to a SD card?

Which Linux firmware file are you using?

Are you using the Rockchip SD Firmware tool, or just using the dd command?

We'd like hear more to complete the "Boot_Ubuntu_from_sd" wiki page. Thank you.

Author: pacopad Time: 12/19/2014 14:06

Hi BusyBee,

i googled and find this distro for rk3288 https://plus.google.com/+IanMORRISON. I burned it with dd on a sdcard and boot.

After that i was able to erase the flash with gparted.

Dont hesitate if you want more details

Pacopad

Welcome Firefly Open Source Community (https://bbs.t-firefly.com/)