Firefly Open Source Community

Title: FreeBSD boot message on Firefly [Print This Page]
Author: ganbold    Time: 1/6/2015 21:58
Title: FreeBSD boot message on Firefly
  1. DDR Version 1.00 20141007
  2. In
  3. Channel a: DDR3 200MHz
  4. Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
  5. Channel b: DDR3 200MHz
  6. Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
  7. Memory OK
  8. Memory OK
  9. OUT


  12. U-Boot 2014.10-RK3288-01-gadc60cd-dirty (Jan 05 2015 - 21:53:02)

  14. CPU: rk3288
  15. CPU's clock information:
  16. arm pll = 600000000HZ
  17. periph pll = 297000000HZ
  18. ddr pll = 200000000HZ
  19. codec pll = 384000000HZ
  20. Board:        Rockchip platform Board
  21. DRAM:  Found dram banks:1
  22. Adding bank:0000000000000000(0000000080000000)
  23. 128 MiB
  24. storage init OK!
  25. Using default environment

  27. GetParam
  28. check parameter success
  29. Unknow param: MACHINE_MODEL:rk30sdk!
  30. Unknow param: MACHINE_ID:007!
  31. Unknow param: MANUFACTURER:RK30SDK!
  32. Unknow param: PWR_HLD: 0,0,A,0,1!
  33. failed to prepare fdt from boot!
  34. power key: bank-0 pin-5
  35. can't find dts node for ricoh619
  36. pmic:act8846
  37. Can't find dts node for fuel guage cw201x
  38. SecureBootEn = 0, SecureBootLock = 0

  40. #Boot ver: 2015-01-05#2.19
  41. sn:1006120001000186
  42. checkKey
  43. vbus = 1
  44. rockusb key pressed.
  45. DDR Version 1.00 20141007
  46. In
  47. SRX
  48. Channel a: DDR3 200MHz
  49. Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
  50. Channel b: DDR3 200MHz
  51. Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
  52. OUT


  55. U-Boot 2014.10-RK3288-01-gadc60cd-dirty (Jan 05 2015 - 21:53:02)

  57. CPU: rk3288
  58. CPU's clock information:
  59. arm pll = 600000000HZ
  60. periph pll = 297000000HZ
  61. ddr pll = 200000000HZ
  62. codec pll = 384000000HZ
  63. Board:        Rockchip platform Board
  64. DRAM:  Found dram banks:1
  65. Adding bank:0000000000000000(0000000080000000)
  66. 128 MiB
  67. storage init OK!
  68. Using default environment

  70. GetParam
  71. check parameter success
  72. Unknow param: MACHINE_MODEL:rk30sdk!
  73. Unknow param: MACHINE_ID:007!
  74. Unknow param: MANUFACTURER:RK30SDK!
  75. Unknow param: PWR_HLD: 0,0,A,0,1!
  76. failed to prepare fdt from boot!
  77. power key: bank-0 pin-5
  78. can't find dts node for ricoh619
  79. pmic:act8846
  80. Can't find dts node for fuel guage cw201x
  81. SecureBootEn = 0, SecureBootLock = 0

  83. #Boot ver: 2015-01-05#2.19
  84. sn:1006120001000186
  85. unknown reboot type 1
  86. no fuel gauge found
  87. no fuel gauge found
  88. read logo_on switch from dts [0]
  89. no fuel gauge found
  90. SecureBootEn = 0, SecureBootLock = 0
  91. failed to find part:04bf0000
  92. kernel   @ 0x62000000 (0x004e47a4)
  93. ramdisk  @ 0x04bf0000 (0x00000000)
  94. Secure Boot state: 0
  95. bootrk: do_bootm_linux...

  97. Starting kernel ...

  99. efgin initarm 1.1
  100. Cin initarm 2, 0xffe90000
  101. in initarm 3, 0xffe90000
  102. in initarm 4
  103. in initarm 5
  104. in initarm 6
  105. in initarm 7
  106. in initarm 8
  107. in initarm 9
  108. in initarm 10
  109. in initarm 101
  110. in initarm 11
  111. in initarm 12
  112. KDB: debugger backends: ddb
  113. KDB: current backend: ddb
  114. in initarm 17
  115. Copyright (c) 1992-2015 The FreeBSD Project.
  116. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
  117. The Regents of the University of California. All rights reserved.
  118. FreeBSD is a registered trademark of The FreeBSD Foundation.
  119. FreeBSD 11.0-CURRENT #112 r276691M: Tue Jan  6 19:10:18 ULAT 2015
  120. tsgan@beastie.micom.mng.net:/usr/obj/arm.armv6/usr/src/sys/FIREFLY arm
  121. FreeBSD clang version 3.5.0 (tags/RELEASE_350/final 216957) 20141124
  122. WARNING: WITNESS option enabled, expect reduced performance.
  123. WARNING: DIAGNOSTIC option enabled, expect reduced performance.
  124. CPU: Cortex A17 rev 1 (Cortex-A core)
  125. Supported features: ARM_ISA THUMB2 JAZELLE THUMBEE ARMv4 Security_Ext
  126. WB disabled EABT branch prediction enabled
  127. LoUU:2 LoC:3 LoUIS:2
  128. Cache level 1:
  129. 32KB/64B 4-way data cache WB Read-Alloc Write-Alloc
  130. 32KB/64B 4-way instruction cache Read-Alloc
  131. Cache level 2:
  132. 1024KB/64B 16-way unified cache WB Read-Alloc Write-Alloc
  133. real memory  = 2147479552 (2047 MB)
  134. avail memory = 2091311104 (1994 MB)
  135. random device not loaded/active; using insecure pseudo-random number generator
  136. random: entropy device infrastructure driver
  137. random: selecting highest priority adaptor
  138. random: SOFT: yarrow init()
  139. random: selecting highest priority adaptor
  140. ofwbus0:
  141. simplebus0:on ofwbus0
  142. gic0:mem 0xffc01000-0xffc01fff,0xffc02000-0xffc02fff on simplebus0
  143. gic0: pn 0x20, arch 0x2, rev 0x1, implementer 0x43b irqs 192
  144. generic_timer0:irq 29,30,27,26 on simplebus0
  145. Timecounter "ARM MPCore Timecounter" frequency 24000000 Hz quality 1000
  146. Event timer "ARM MPCore Eventtimer" frequency 24000000 Hz quality 1000
  147. rk30_pmu0:mem 0xff730000-0xff7300ff on simplebus0
  148. rk30_grf0:mem 0xff770000-0xff771fff on simplebus0
  149. gpio0:mem 0xff750000-0xff7500ff irq 113 on simplebus0
  150. gpioc0:on gpio0
  151. gpiobus0:on gpio0
  152. gpio1:mem 0xff780000-0xff7800ff irq 114 on simplebus0
  153. gpioc1:on gpio1
  154. gpiobus1:on gpio1
  155. gpio2:mem 0xff790000-0xff7900ff irq 115 on simplebus0
  156. gpioc2:on gpio2
  157. gpiobus2:on gpio2
  158. gpio3:mem 0xff7a0000-0xff7a00ff irq 116 on simplebus0
  159. gpioc3:on gpio3
  160. gpiobus3:on gpio3
  161. gpio4:mem 0xff7b0000-0xff7b00ff irq 117 on simplebus0
  162. gpioc4:on gpio4
  163. gpiobus4:on gpio4
  164. gpio5:mem 0xff7c0000-0xff7c00ff irq 118 on simplebus0
  165. gpioc5:on gpio5
  166. gpiobus5:on gpio5
  167. gpio6:mem 0xff7d0000-0xff7d00ff irq 119 on simplebus0
  168. gpioc6:on gpio6
  169. gpiobus6:on gpio6
  170. gpio7:mem 0xff7e0000-0xff7e00ff irq 120 on simplebus0
  171. gpioc7:on gpio7
  172. gpiobus7:on gpio7
  173. gpio8:mem 0xff7f0000-0xff7f00ff irq 121 on simplebus0
  174. gpioc8:on gpio8
  175. gpiobus8:on gpio8
  176. dwcotg0: mem 0xff580000-0xff5bffff irq 55 on simplebus0
  177. usbus0 on dwcotg0
  178. dwcotg1: mem 0xff540000-0xff57ffff irq 57 on simplebus0
  179. usbus1 on dwcotg1
  180. Timecounters tick every 10.000 msec
  181. usbus0: 480Mbps High Speed USB v2.0
  182. usbus1: 480Mbps High Speed USB v2.0
  183. random: unblocking device.
  184. WARNING: WITNESS option enabled, expect reduced performance.
  185. WARNING: DIAGNOSTIC option enabled, expect reduced performance.
  186. ugen0.1:at usbus0
  187. uhub0: on usbus0
  188. ugen1.1:at usbus1
  189. uhub1: on usbus1
  190. uhub1: 1 port with 1 removable, self powered
  191. uhub0: 1 port with 1 removable, self powered
  192. usb_alloc_device: setting up USB template failed maybe the USB template module has not been loaded
  193. ugen0.2:at usbus0 (disconnected)
  194. uhub_reattach_port: could not allocate new device
  195. ugen1.2:at usbus1
  196. uhub2: on usbus1
  197. uhub2: MTT enabled
  198. Root mount waiting for: usbus1
  199. uhub2: 4 ports with 4 removable, self powered
  200. Root mount waiting for: usbus1
  201. Root mount waiting for: usbus1
  202. ugen1.3: at usbus1
  203. umass0: on usbus1
  204. umass0:  SCSI over Bulk-Only; quirks = 0x4100
  205. umass0:0:0: Attached to scbus0
  206. Trying to mount root from ufs:/dev/da0 []...
  207. mountroot: waiting for device /dev/da0 ...
  208. da0 at umass-sim0 bus 0 scbus0 target 0 lun 0
  209. da0: Removable Direct Access SCSI-2 device
  210. da0: Serial Number 15213301BF1BC700
  211. da0: 40.000MB/s transfers
  212. da0: 3998MB (8187904 512 byte sectors: 255H 63S/T 509C)
  213. da0: quirks=0x3
  214. WARNING: / was not properly dismounted
  215. warning: no time-of-day clock registered, system time will not be set accurately
  216. Expensive timeout(9) function: 0xc20642b0(0xc7228000) 0.002127708 s
  217. usb_alloc_device: setting up USB template failed maybe the USB template module has not been loaded
  218. ugen0.2:at usbus0 (disconnected)
  219. uhub_reattach_port: could not allocate new device
  220. usb_alloc_device: setting up USB template failed maybe the USB template module has not been loaded
  221. ugen0.2:at usbus0 (disconnected)
  222. uhub_reattach_port: could not allocate new device
  223. usb_alloc_device: setting up USB template failed maybe the USB template module has not been loaded
  224. ugen0.2:at usbus0 (disconnected)
  225. uhub_reattach_port: could not allocate new device
  226. usb_alloc_device: setting up USB template failed maybe the USB template module has not been loaded
  227. ugen0.2:at usbus0 (disconnected)
  228. uhub_reattach_port: could not allocate new device
  229. usb_alloc_device: setting up USB template failed maybe the USB template module has not been loaded
  230. ugen0.2:at usbus0 (disconnected)
  231. uhub_reattach_port: could not allocate new device
  232. usb_alloc_device: setting up USB template failed maybe the USB template module has not been loaded
  233. ugen0.2:at usbus0 (disconnected)
  234. uhub_reattach_port: could not allocate new device
  235. usb_alloc_device: setting up USB template failed maybe the USB template module has not been loaded
  236. ugen0.2:at usbus0 (disconnected)
  237. uhub_reattach_port: could not allocate new device
  238. usb_alloc_device: setting up USB template failed maybe the USB template module has not been loaded
  239. ugen0.2:at usbus0 (disconnected)
  240. uhub_reattach_port: could not allocate new device
  241. usb_alloc_device: setting up USB template failed maybe the USB template module has not been loaded
  242. ugen0.2:at usbus0 (disconnected)
  243. uhub_reattach_port: could not allocate new device
Copy the code

Author: busybee    Time: 1/8/2015 14:33
Hi @ganbold , what can we do for you?
You can PM me.
Author: ganbold    Time: 1/9/2015 18:49
I would like to have RK3288 TRM if possible, because uart driver is not working yet for FreeBSD and I wanted to make sure about physical memory start address and kernel load address. Looking at linux source or u-boot source is sometimes hard and sometimes there are too many sources and all seem to different.
Author: ganbold    Time: 1/11/2015 14:09

Better but still no uart yet.





https://github.com/tsgan/rockchip/blob/ ... -print.txt
Author: ganbold    Time: 1/12/2015 13:28
Full boot msg in multi-user mode

https://github.com/tsgan/rockchip/blob/ ... i-user.txt
  1. DDR Version 1.00 20141007
  2. In
  3. SRX
  4. Channel a: DDR3 200MHz
  5. Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
  6. Channel b: DDR3 200MHz
  7. Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
  8. OUT


  11. U-Boot 2014.10-RK3288-01-gadc60cd-dirty (Jan 10 2015 - 11:21:08)

  13. CPU: rk3288
  14. CPU's clock information:
  15.     arm pll = 600000000HZ
  16.     periph pll = 297000000HZ
  17.     ddr pll = 200000000HZ
  18.     codec pll = 384000000HZ
  19. Board:        Rockchip platform Board
  20. DRAM:  Found dram banks:1
  21. Adding bank:0000000000000000(0000000080000000)
  22. 128 MiB
  23. storage init OK!
  24. Using default environment

  26. GetParam
  27. check parameter success
  28. Unknow param: MACHINE_MODEL:rk30sdk!
  29. Unknow param: MACHINE_ID:007!
  30. Unknow param: MANUFACTURER:RK30SDK!
  31. Unknow param: PWR_HLD: 0,0,A,0,1!
  32. failed to prepare fdt from boot!
  33. power key: bank-0 pin-5
  34. can't find dts node for ricoh619
  35. pmic:act8846
  36. Can't find dts node for fuel guage cw201x
  37. SecureBootEn = 0, SecureBootLock = 0

  39. #Boot ver: 2015-01-10#2.19
  40. sn:1006120001000186
  41. unknown reboot type 1
  42. no fuel gauge found
  43. no fuel gauge found
  44. read logo_on switch from dts [0]
  45. no fuel gauge found
  46. SecureBootEn = 0, SecureBootLock = 0
  47. failed to find part:04bf0000
  48. kernel   @ 0x60400000 (0x004ea724)
  49. ramdisk  @ 0x04bf0000 (0x00000000)
  50. Secure Boot state: 0
  51. bootrk: do_bootm_linux...

  53. Starting kernel ...

  55. in initarm 6
  56. in initarm 7
  57. in initarm 8
  58. in initarm 9
  59. in initarm 10
  60. in initarm 101
  61. in initarm 11
  62. in initarm 12
  63. KDB: debugger backends: ddb
  64. KDB: current backend: ddb
  65. in initarm 17
  66. Copyright (c) 1992-2015 The FreeBSD Project.
  67. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
  68.         The Regents of the University of California. All rights reserved.
  69. FreeBSD is a registered trademark of The FreeBSD Foundation.
  70. FreeBSD 11.0-CURRENT #159 r276691M: Mon Jan 12 12:51:13 ULAT 2015
  71.     tsgan@beastie.micom.mng.net:/usr/obj/arm.armv6/usr/src/sys/FIREFLY arm
  72. FreeBSD clang version 3.5.0 (tags/RELEASE_350/final 216957) 20141124
  73. WARNING: WITNESS option enabled, expect reduced performance.
  74. WARNING: DIAGNOSTIC option enabled, expect reduced performance.
  75. CPU: Cortex A17 rev 1 (Cortex-A core)
  76. Supported features: ARM_ISA THUMB2 JAZELLE THUMBEE ARMv4 Security_Ext
  77. WB disabled EABT branch prediction enabled
  78. LoUU:2 LoC:3 LoUIS:2
  79. Cache level 1:
  80. 32KB/64B 4-way data cache WB Read-Alloc Write-Alloc
  81. 32KB/64B 4-way instruction cache Read-Alloc
  82. Cache level 2:
  83. 1024KB/64B 16-way unified cache WB Read-Alloc Write-Alloc
  84. real memory  = 2147479552 (2047 MB)
  85. avail memory = 2091266048 (1994 MB)
  86. random device not loaded/active; using insecure pseudo-random number generator
  87. random: entropy device infrastructure driver
  88. random: selecting highest priority adaptor <Dummy>
  89. random: SOFT: yarrow init()
  90. random: selecting highest priority adaptor <Yarrow>
  91. ofwbus0: <Open Firmware Device Tree>
  92. simplebus0: <Flattened device tree simple bus> on ofwbus0
  93. gic0: <ARM Generic Interrupt Controller> mem 0xffc01000-0xffc01fff,0xffc02000-0xffc02fff on simplebus0
  94. gic0: pn 0x20, arch 0x2, rev 0x1, implementer 0x43b irqs 192
  95. generic_timer0: <ARMv7 Generic Timer> irq 29,30,27,26 on simplebus0
  96. Timecounter "ARM MPCore Timecounter" frequency 24000000 Hz quality 1000
  97. Event timer "ARM MPCore Eventtimer" frequency 24000000 Hz quality 1000
  98. rk30_pmu0: <RK30XX PMU> mem 0xff730000-0xff7300ff on simplebus0
  99. rk30_grf0: <RK30XX General Register File> mem 0xff770000-0xff771fff on simplebus0
  100. gpio0: <Rockchip RK30XX GPIO controller> mem 0xff750000-0xff7500ff irq 113 on simplebus0
  101. gpioc0: <GPIO controller> on gpio0
  102. gpiobus0: <GPIO bus> on gpio0
  103. gpio1: <Rockchip RK30XX GPIO controller> mem 0xff780000-0xff7800ff irq 114 on simplebus0
  104. gpioc1: <GPIO controller> on gpio1
  105. gpiobus1: <GPIO bus> on gpio1
  106. gpio2: <Rockchip RK30XX GPIO controller> mem 0xff790000-0xff7900ff irq 115 on simplebus0
  107. gpioc2: <GPIO controller> on gpio2
  108. gpiobus2: <GPIO bus> on gpio2
  109. gpio3: <Rockchip RK30XX GPIO controller> mem 0xff7a0000-0xff7a00ff irq 116 on simplebus0
  110. gpioc3: <GPIO controller> on gpio3
  111. gpiobus3: <GPIO bus> on gpio3
  112. gpio4: <Rockchip RK30XX GPIO controller> mem 0xff7b0000-0xff7b00ff irq 117 on simplebus0
  113. gpioc4: <GPIO controller> on gpio4
  114. gpiobus4: <GPIO bus> on gpio4
  115. gpio5: <Rockchip RK30XX GPIO controller> mem 0xff7c0000-0xff7c00ff irq 118 on simplebus0
  116. gpioc5: <GPIO controller> on gpio5
  117. gpiobus5: <GPIO bus> on gpio5
  118. gpio6: <Rockchip RK30XX GPIO controller> mem 0xff7d0000-0xff7d00ff irq 119 on simplebus0
  119. gpioc6: <GPIO controller> on gpio6
  120. gpiobus6: <GPIO bus> on gpio6
  121. gpio7: <Rockchip RK30XX GPIO controller> mem 0xff7e0000-0xff7e00ff irq 120 on simplebus0
  122. gpioc7: <GPIO controller> on gpio7
  123. gpiobus7: <GPIO bus> on gpio7
  124. gpio8: <Rockchip RK30XX GPIO controller> mem 0xff7f0000-0xff7f00ff irq 121 on simplebus0
  125. gpioc8: <GPIO controller> on gpio8
  126. gpiobus8: <GPIO bus> on gpio8
  127. dwcotg0: <DWC OTG 2.0 integrated USB controller> mem 0xff580000-0xff5bffff irq 55 on simplebus0
  128. usbus0 on dwcotg0
  129. dwcotg1: <DWC OTG 2.0 integrated USB controller> mem 0xff540000-0xff57ffff irq 57 on simplebus0
  130. usbus1 on dwcotg1
  131. uart0: <16750 or compatible> mem 0xff690000-0xff6903ff irq 89 on simplebus0
  132. uart0: console (115200,n,8,1)
  133. Timecounters tick every 10.000 msec
  134. usbus0: 480Mbps High Speed USB v2.0
  135. usbus1: 480Mbps High Speed USB v2.0
  136. random: unblocking device.
  137. WARNING: WITNESS option enabled, expect reduced performance.
  138. WARNING: DIAGNOSTIC option enabled, expect reduced performance.
  139. ugen0.1: <DWCOTG> at usbus0
  140. uhub0: <DWCOTG OTG Root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0
  141. ugen1.1: <DWCOTG> at usbus1
  142. uhub1: <DWCOTG OTG Root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1
  143. uhub1: 1 port with 1 removable, self powered
  144. uhub0: 1 port with 1 removable, self powered
  145. usb_alloc_device: setting up USB template failed maybe the USB template module has not been loaded
  146. ugen0.2: <Unknown> at usbus0 (disconnected)
  147. uhub_reattach_port: could not allocate new device
  148. ugen1.2: <vendor 0x1a40> at usbus1
  149. uhub2: <vendor 0x1a40 USB 2.0 Hub MTT, class 9/0, rev 2.00/1.00, addr 2> on usbus1
  150. uhub2: MTT enabled
  151. Root mount waiting for: usbus1
  152. uhub2: 4 ports with 4 removable, self powered
  153. Root mount waiting for: usbus1
  154. Root mount waiting for: usbus1
  155. ugen1.3: <USB 2.0> at usbus1
  156. umass0: <USB 2.0 Flash Disk, class 0/0, rev 2.00/1.00, addr 3> on usbus1
  157. umass0:  SCSI over Bulk-Only; quirks = 0x4100
  158. umass0:0:0: Attached to scbus0
  159. da0 at umass-sim0 bus 0 scbus0 target 0 lun 0
  160. da0: <USB 2.0 Flash Disk 5.00> Removable Direct Access SCSI-2 device
  161. da0: Serial Number 15213301BF1BC700
  162. da0: 40.000MB/s transfers
  163. da0: 3998MB (8187904 512 byte sectors: 255H 63S/T 509C)
  164. da0: quirks=0x3<NO_SYNC_CACHE,NO_6_BYTE>
  165. Trying to mount root from ufs:/dev/da0 []...
  166. warning: no time-of-day clock registered, system time will not be set accurately
  167. Setting hostuuid: 249385b8-be3d-11e3-a644-678d5837e307.
  168. Setting hostid: 0xd8d50f9f.
  169. No suitable dump device was found.
  170. Entropy harvesting:sysctl: unknown oid 'kern.random.sys.harvest.interrupt': No such file or directory
  171. interruptssysctl: unknown oid 'kern.random.sys.harvest.ethernet': No such file or directory
  172. ethernetsysctl: unknown oid 'kern.random.sys.harvest.point_to_point': No such file or directory
  173. point_to_pointsysctl: unknown oid 'kern.random.sys.harvest.swi': No such file or directory
  174. swi.
  175. Starting file system checks:
  176. /dev/da0: FILE SYSTEM CLEAN; SKIPPING CHECKS
  177. /dev/da0: clean, 572815 free (3335 frags, 71185 blocks, 0.3% fragmentation)
  178. Mounting local file systems:.
  179. Writing entropy file:usb_alloc_device: setting up USB template failed maybe the USB template module has not been loaded
  180. ugen0.2: <Unknown> at usbus0 (disconnected)
  181. uhub_reattach_port: could not allocate new device
  182. .
  183. Setting hostname: arm.
  184. Starting Network: lo0.
  185. lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
  186.         options=600003<RXCSUM,TXCSUM,RXCSUM_IPV6,TXCSUM_IPV6>
  187.         inet6 ::1 prefixlen 128
  188.         inet6 fe80::1%lo0 prefixlen 64 scopeid 0x1
  189.         inet 127.0.0.1 netmask 0xff000000
  190.         nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
  191. Starting devd.
  192. Starting pflogd:
  193. add net fe80::: gateway ::1
  194. add net ff02::: gateway ::1
  195. add net ::ffff:0.0.0.0: gateway ::1
  196. add net ::0.0.0.0: gateway ::1
  197. Creating and/or trimming log files.
  198. Starting syslogd.
  199. ELF ldconfig path: /lib /usr/lib /usr/lib/compat /usr/local/lib
  200. Starting casperd.
  201. Clearing /tmp (X related).
  202. usb_alloc_device: setting up USB template failed maybe the USB template module has not been loaded
  203. ugen0.2: <Unknown> at usbus0 (disconnected)
  204. uhub_reattach_port: could not allocate new device
  205. Updating motd:.
  206. Mounting late file systems:.
  207. Performing sanity check on sshd configuration.
  208. Starting sshd.
  209. Starting sendmail_submit.
  210. Starting sendmail_msp_queue.
  211. Starting cron.
  212. Jan 12 13:13:14 arm sm-mta[535]: s940mWXg007341: SYSERR(root): hash map "Alias0": missing map file /etc/mail/aliases.db: No such file or directory
  213. usb_alloc_device: setting up USB template failed maybe the USB template module has not been loaded
  214. ugen0.2: <Unknown> at usbus0 (disconnected)
  215. uhub_reattach_port: could not allocate new device
  216. Starting background file system checks in 60 seconds.

  218. Mon Jan 12 13:13:21 ULAT 2015

  220. FreeBSD/arm (arm) (ttyu0)

  222. login: root
  223. Jan 12 13:13:25 arm login: ROOT LOGIN (root) ON ttyu0
  224. Last login: Wed Oct  1 18:39:36 on ttyu0
  225. FreeBSD 11.0-CURRENT (FIREFLY) #159 r276691M: Mon Jan 12 12:51:13 ULAT 2015

  227. Welcome to FreeBSD!

  229. Before seeking technical support, please use the following resources:

  231. o  Security advisories and updated errata information for all releases are
  232.    at http://www.FreeBSD.org/releases/ - always consult the ERRATA section
  233.    for your release first as it's updated frequently.

  235. o  The Handbook and FAQ documents are at http://www.FreeBSD.org/ and,
  236.    along with the mailing lists, can be searched by going to
  237.    http://www.FreeBSD.org/search/.  If the doc package has been installed
  238.    (or fetched via pkg install lang-freebsd-doc, where lang is the
  239.    2-letter language code, e.g. en), they are also available formatted
  240.    in /usr/local/share/doc/freebsd.

  242. If you still have a question or problem, please take the output of
  243. `uname -a', along with any relevant error messages, and email it
  244. as a question to the questions@FreeBSD.org mailing list.  If you are
  245. unfamiliar with FreeBSD's directory layout, please refer to the hier(7)
  246. manual page.  If you are not familiar with manual pages, type `man man'.

  248. Edit /etc/motd to change this login announcement.

  250. You have new mail.
  251. usb_alloc_device: setting up USB template failed maybe the USB template module has not been loaded
  252. ugen0.2: <Unknown> at usbus0 (disconnected)
  253. uhub_reattach_port: could not allocate new device
  254. root@arm:~ # uname -an
  255. FreeBSD arm 11.0-CURRENT FreeBSD 11.0-CURRENT #159 r276691M: Mon Jan 12 12:51:13 ULAT 2015     tsgan@beastie.micom.mng.net:/usr/obj/arm.armv6/usr/src/sys/FIREFLY  arm
  256. root@arm:~ # id
  257. uid=0(root) gid=0(wheel) groups=0(wheel),5(operator)
  258. root@arm:~ #
Copy the code



Author: Sencher    Time: 1/25/2025 15:50
Last edited by Sencher In 1/25/2025 15:52 Editor

good
Author: Sencher    Time: 1/25/2025 15:51
Title: RE: FreeBSD boot message on Firefly
Navigating trademark rights can feel complex, but protecting intellectual property is vital for organizations like The Regents of the University of California or The FreeBSD Foundation. For businesses, securing your brand is easier with top-Rated Trademark Registration Services in Tennessee, ensuring your name is protected and recognized, especially in competitive markets.



Welcome Firefly Open Source Community (https://bbs.t-firefly.com/) Powered by Discuz! X3.1