Title: [Firefly-RK3399] system is stuck at logo(blur image) not booting up [Print This Page] Author: Learner379 Time: 6/18/2020 19:48 Title: [Firefly-RK3399] system is stuck at logo(blur image) not booting up Hi,
I have flashed Android 7 image on to the Firefly-RK3399 board. System once booted up normally. But after few boot cycles, system is stuck and not booting up.
Please refer the serial console logs attached below.
U-Boot 2017.02-RK3399-06 (Jun 16 2020 - 15:11:29)
CPU: rk3399
cpu version = 0
CPU's clock information:
aplll = 816000000HZ
apllb = 24000000HZ
gpll = 800000000HZ
aclk_periph_h = 133333333HZ, hclk_periph_h = 66666666HZ, pclk_periph_h = 33333333HZ
aclk_periph_l0 = 100000000HZ, hclk_periph_l0 = 100000000HZ, pclk_periph_l0 = 50000000HZ
hclk_periph_l1 = 100000000HZ, pclk_periph_l1 = 50000000HZ
cpll = 800000000HZ
dpll = 666000000HZ
vpll = 24000000HZ
npll = 24000000HZ
ppll = 676000000HZ
Board: Rockchip platform Board
Uboot as second level loader
DRAM: Found dram banks: 1
Adding bank:0000000000200000(000000007fe00000)
Reserve memory for trust os.
dram reserve bank: base = 0x08400000, size = 0x01e00000
128 MiB
SdmmcInit = 0 20
storage init OK!
Using default environment
#Boot ver: 2020-06-16#1.09
empty serial no.
normal boot.
checkKey
vbus = 1
board_fbt_key_pressed: ir_keycode = 0x0, frt = 0
no fuel gauge found
no fuel gauge found
failed to find panel driver
read logo on state from dts [1]
no fuel gauge found
can't find dts node for deviceinfo
dw_rk_hdmi_register:fail to read deviceinfo
hdmi baseparamer 0x0@0-0
[EDID-EXTEND] It is a CEA 861 Series Extension.
no baseparametr,find best edid mode,vic=16
hdmi_dev->video.vic is 16
rk lcdc - 0 dclk set: dclk = 148500000HZ, pll select = 0, div = 1
rockchip_panel_prepare: failed to find panel prepare funcs
hdmi_dev_config_video vic 16 color_output 3 color_output_depth 8
pixel clk is 148500000 tmds clk is 148500000
hsync_pol 1 vsync_pol 1
[HDMI] sucess output HDMI.
PHY PLL not locked: PCLK_ON=1,TMDSCLK_ON=1
rockchip_panel_enable: failed to find panel prepare funcs
ERROR: [get_entry_ram]: Cannot find logo_kernel.bmp!
failed to display kernel logo
checkKey
vbus = 1
board_fbt_key_pressed: ir_keycode = 0x0, frt = 0
got recovery cmd from misc.
load fdt from resouce.
vendor read error!
Set oem_unlocked=0Secure Boot state: 0
kernel @ 0x00280000 (0x01238008)
ramdisk @ 0x04bf0000 (0x007b21c4)
bootrk: do_bootm_linux...
Loading Device Tree to 0000000004600000, end 0000000004615675 ... OK
Add bank:0000000000200000, 0000000008200000
Add bank:000000000a200000, 0000000075e00000
WARNING: could not set reg FDT_ERR_BADOFFSET.
Tried flashing some other factory images as well, but still system is not booting. Please let me know, if you people know any solution to resolve this issue.
Author: phkr Time: 6/19/2020 15:38
I had some similar crash using custom image with kernel and u-boot from slarm64 when i tried to perform a large disk operation. In my case building mainline u-boot was a solutionAuthor: Learner379 Time: 6/25/2020 14:42 Last edited by Learner379 In 6/26/2020 13:12 Editor
phkr Posted at 6/19/2020 15:38
I had some similar crash using custom image with kernel and u-boot from slarm64 when i tried to perf ...
Thanks for your reply.
In my case, I have new board, earlier it had one factory image then I flashed locally built clean image then I was facing the above mentioned issue. After that tried flashing factory image(which was working earlier) also, still same issue is coming. Any idea how to deal with this situation?Author: maxlee433 Time: 1/11/2026 22:41
That article had a huge impact on me. The NCP-DB-6.10 Online Test material is superb, and itĄŻs available for free.Author: tedcole263 Time: 1/17/2026 15:04
It was such a valuable learning experience. Taking the Latest 350-501 exam experience exam soon, hope IĄŻll do well!Author: sarahmi537 Time: 1/19/2026 23:44
IĄŻm completely in awe of your article, thank you for sharing! I advanced with the Valid study guide 1Z0-1081-24 ppt, earning a promotion and salary increase. Now, itĄŻs free for everyone. Best of luck with your own promotions!
Welcome Firefly Open Source Community (https://bbs.t-firefly.com/)