完璧-一番優秀なHPE7-A06資格試験試験-試験の準備方法HPE7-A06認定試験私たちが知っているように、一部の人々は以前に試験に失敗し、HPE7-A06トレーニング資料を購入する前にこの苦しい試験に自信を失いました。私たちはここで悲しみを分けます。これから時間のかかる思考を捨てることができます。対照的に、それらは不明瞭なコンテンツを感じることなくあなたの可能性を刺激します。 HPE7-A06試験準備を取得した後、試験期間中に大きなストレスにさらされることはありません。 HPE Campus Access Switching Expert Written Exam 認定 HPE7-A06 試験問題 (Q76-Q81):質問 # 76
An engineer finds that a specific HPE switch interface has high error rates. Which two parameters are most likely causing this issue?
A. VLAN misconfiguration
B. Port speed
C. LACP mode
D. Duplex mismatch
正解：B、D
質問 # 77
You are configuring an HPE Aruba Networking Gateway Cluster with AOS-10. What is true about
802.1X functionality in combination with gateways? (Choose two.)
A. Users on L3-connected gateways need to perform a full authentication after re-associated on the AP.
B. The gateways are used as a RADIUS proxy, while the AP is the authenticator.
C. Regardless of using gateways, the CoA message is always sent to the APs.
D. The gateways act as RADIUS Proxy only in Tunneled and Bridged Mode.
E. The UDG remains fixed on L2-connected gateways but not on L3-connected gateways.
正解：A、B
解説：
In L3-connected gateway designs, a full 802.1X authentication is required after AP re-association because session state is not preserved across gateway re-association.
In AOS-10, the AP is the authenticator, but the gateway functions as the RADIUS proxy, forwarding requests to the RADIUS server. This ensures centralized control and policy enforcement.
質問 # 78
With the configuration of two CX 8325 switches in the VSX cluster, how would you prepare a link- aggregation for a 7000 gateway for a zero-touch provision to support protocol-based port redundancy?
A.
B.
C.
D.
正解：B
解説：
To support protocol-based port redundancy (zero-touch provisioning) with a 7000 gateway and two CX 8325 VSX switches, you must configure lacp mode active and lacp fallback on a multi- chassis LAG. This ensures the gateway can form an LACP port-channel with either switch even before LACP negotiation begins, providing redundancy and seamless provisioning.
質問 # 79
You are about to deploy a gateway that is on factory default. ZTP cannot be used for different reasons, but you are searching for valid alternatives. What are two valid alternatives for ZTP?
(Choose two.)
A. Use OTP by connecting to port 0/0/0, and use a Web browser to complete provisioning.
B. Use OTP by connecting to console port, and use terminal software to complete provisioning. "Full- Setup" should be used.
C. Use OTP by connecting to port 0/0/1, and use a Web browser to complete provisioning.
D. Use OTP by connecting to port 0/0/1 with a static IP, and use a Web browser to complete provisioning.
E. Use OTP by connecting to console port, and use terminal software provisioning. "Static-Activate" should be used.
正解：A、B
解説：
Correct - You can connect to port 0/0/0 with a web browser and complete provisioning using One-Touch Provisioning (OTP).
Correct - You can connect via the console port and use terminal software with the "full-setup" option to complete OTP provisioning.
質問 # 80
Why is "linkup-delay-timer exclude lag-list" used in a VSX configuration?
A. to perform MSTP calculations correctly during the link-up delay
B. to allow upstream router adjacencies to be established during the link-up delay
C. to exclude every LAG where another switch is connected during the link-up delay
D. to ensure the ISL link is not blocked during the link-up delay
正解：C
解説：
The linkup-delay-timer exclude lag-list command in a VSX configuration is used to exclude specific LAG interfaces that connect to other switches from the global link-up delay mechanism.
By default, the link-up delay timer holds down all interfaces for a defined period after a reboot to prevent loops and ensure stability. However, inter-switch connections (like LAGs to other switches) should not be delayed, as they are essential for fast VSX peer synchronization.
Excluding these LAGs ensures they come up immediately while still applying the delay to other access-facing ports.
