最有效的300-510考試證照綜述,免費下載300-510考試資料幫助妳通過300-510考試在現在這個競爭激烈的社會裏,有一技之長是可以占很大優勢的。尤其在IT行業中.。獲到一些IT認證證書是非常有用的。 Cisco 300-510 是一個檢驗IT專業知識水準認證考試,在IT行業中也是一個分量相當重的認證考試。因為Cisco 300-510考試難度也比較大,所以很多為了通過Cisco 300-510 認證考試的人花費了大量的時間和精力學習考試相關知識,但是到最後卻沒有成功。PDFExamDumps為此分析了他們失敗的原因,我們得出的結論是他們沒有經過針對性的培訓。 現在PDFExamDumps的專家們為Cisco 300-510 認證考試研究出了針對性的訓練項目,可以幫你花少量時間和金錢卻可以100%通過考試。 最新的 CCNP Service Provider 300-510 免費考試真題 (Q97-Q102):問題 #97
Refer to the exhibit. Which router does R1 install as an alternate next hop when trying to reach R3 if LFA is enabled?
A. R3
B. R2
C. R4
D. R5
答案:B
問題 #98
A network engineer must configure a Cisco IOS XR router with BGP dampening.
Which configuration meets these parameters?
A. router bgp 60
address-family ipv4 unicast
bgp dampening
B. router bgp 60
neighbor 10.0.0.2
bgp dampening
C. route-policy dampening_specific
drop
!
router bgp 60
address-family ipv4 unicast
bgp dampening route-policy dampening_specific
D. router bgp 60
bgp dampening
E. router bgp 60
address-family ipv4
bgp dampening
答案:A
問題 #99
Refer to the exhibit.
Refer to the exhibit. The initial BGP configuration of the network is complete, and all the routers have established BGP neighborship. The engineer configured Router 2 with additional BGP paths to install and advertise more paths to Router 1 and Router 3. Which configuration must the engineer apply to Router 1 and Router 3 so that they will use and install all additional paths?
A. Option D
B. Option A
C. Option B
D. Option C
答案:A
問題 #100
Refer to the exhibit. An engineer is troubleshooting an issue with traffic steering using the color-only automated steering mechanism. BGP is failing to automatically steer traffic into an SR policy with the given color of a route, regardless of the next hop. The layer 2 configuration is correct, and the physical connection between the devices is working normally. Whch additional command sequence must the engineer add to correct the issue?
A. Option D
B. Option A
C. Option B
D. Option C
答案:A
問題 #101
Refer to the exhibit. IS-IS runs in the network and all routers are in the same area R1 statically routes to distribute traffic with R6 and the networking team has redistributed the static routes on R1 into IS-IS. Hosts on R3 need access to servers connected to R6. A tag has been applied to the routes to manipulate routes along the path but routers running IS-IS are still unable to reach the redistributed routes. Which action must the team take to resolve the issue?
A. Configure the IS-IS routers with metric-style wide
B. Configure the routers as Level 1/Level 2 routers
C. Configure the route map with an additional route-map set-tag permit 10 sequence
D. Configure R3 with a default route that uses R2 as the next hop