Title: Portrait mode [Print This Page] Author: liatoss Time: 5/26/2015 22:39 Title: Portrait mode Last edited by liatoss In 6/11/2015 23:20 Editor
Dear Developers,
Actually today (25.05.2015), does the Firefly RK3288 supports the portrait mode in Android or in Lubuntu? Any third party distros which support the Portrait mode?
Thank you in advance, Vlad.Author: madman Time: 5/27/2015 09:30
Hello,
Revert "Android->frameworks:Forced rotation to horizontal screen if insert hdmi"
This reverts commit 137bead4fffd7f212ee144456420933d54fbd0ef.
you can chance the “true” to “false” or git revert it Author: liatoss Time: 6/8/2015 19:17 Last edited by liatoss In 6/8/2015 19:22 Editor
Hello Madman, thank you very much for quick reply...
It takes time for me but I have compiled a system image, a kernel image etc.... I've got all required images and furthermore I've built a new complete image.
All my similar attempts to fix the issue give me nothing. The board is still in the loop. My attempt to write FirFly original images for the latest Android image as well as for the Dual boot image gives my the same loop.
To clarify, I write parameters file by using the Android Tool release 2.33. It doesn;t work - the same loop. After that, I have made a full image by unpacking the latest Android image I have downloaded from your website and packed it back with my boot.img, kernel.img, misc.img. recovery.img, resource.img, system.img in Ubunut 14.10. In this time RKBatchTool v.1.7 wrote the image but I still got the loop.
Hereby is the text of the loop, which ends by a string "OUT" and after that it repeats the same again and again:
**************** Start of the boot listing *****************************
U-Boot 2014.10-RK3288-02 (Jan 21 2015 - 17:07:53)
CPU: rk3288
CPU's clock information:
arm pll = 600000000HZ
periph pll = 300000000HZ
ddr pll = 200000000HZ
codec pll = 594000000HZ
Board: Rockchip platform Board
DRAM: Found dram banks:1
Adding bank:0000000000000000(0000000080000000)
128 MiB
storage init OK!
Using default environment
GetParam
check parameter success
Unknow param: MACHINE_MODEL:rk30sdk!
Unknow param: MACHINE_ID:007!
Unknow param: MANUFACTURER:RK30SDK!
Unknow param: PWR_HLD: 0,0,A,0,1!
failed to prepare fdt from boot!
power key: bank-0 pin-5
light power led: bank-8 pin-1
pmic:act8846
SecureBootEn = 0, SecureBootLock = 0
#Boot ver: 2015-01-21#2.17
empty serial no.
checkKey
vbus = 1
no fuel gauge found
no fuel gauge found
read logo_on switch from dts [0]
no fuel gauge found
got recovery cmd from misc.
failed to load fdt from recovery!
kernel @ 0x02000000 (0x00653540)
ramdisk @ 0x04bf0000 (0x003dc705)
Secure Boot state: 0
bootrk: do_bootm_linux...
Loading Device Tree to 04808000, end 04826935 ... OK
Add bank:0000000000000000, 0000000080000000
Starting kernel ...
DDR Version 1.00 20141007
In
Channel a: DDR3 200MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
Channel b: DDR3 200MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
Memory OK
Memory OK
OUT
******************** End of the boot listing *********************
By now the card is dead as I cannot use it. Please give me any idea how I can fix it?
I used Windows and Linux tools - the same result. It looks like the card doesn't allow to write parameters file and thus it cycled in the boot sequence.
Thank you for any help,
Vlad.Author: liatoss Time: 6/9/2015 14:00
I opened a new topic as follows: http://bbs.t-firefly.com/forum.php?mod=viewthread&tid=559Author: liatoss Time: 6/10/2015 03:50
Well, In my case, the reason of the kernel loop was the power cable. I took a USB cable from Cubieboard and it power up the board just to flash. However, as soon as the board starts, the board doesn't have enough power and the board reboots.
All of a sudden, I realized, I have another USB cable, the original one. As soon as I replaced the power cable, the board starts working and the boot continues...
By now, I can confirm the board can work in "Portrait mode" as flashing the new compiled image brought me the board in the Portrait mode even at the boot...
Thank you for your guidance,
Vlad.Author: liatoss Time: 6/11/2015 23:22
It looks like the code change doesn't work in not pad versin of the firmware. Can you clarify what shell I change in non pad version of the firmware?
Thank you, Vlad.Author: amadeo700 Time: 3/28/2025 03:09
Could the problem be Drupal? Perhaps you should contact a professional who can offer Drupal maintenance services, and that way your problem will surely be resolved. What do you think? Wouldn't this work as a solution? At least consider what I just told you. It may be the solution to your problem. I hope my comment is helpful. Best regards.Author: Diana92 Time: 3/31/2025 04:01
Migrating from Drupal can be complex, especially when dealing with version upgrades, module compatibility, and data integrity. Issues like deprecated features, custom code adjustments, and performance optimizations often arise, requiring careful planning. If you’re facing difficulties, professional assistance can make the process smoother. I recommend checking out drupal migration services, where experts can handle everything from site audits to full-scale migrations. A structured approach ensures security, functionality, and a seamless transition.Author: Michaell123 Time: 4/2/2025 02:37
Updating Drupal is a serious thing. Especially since version 7. It has a completely different code base. I tried several times to do it myself, but still ended up with something not working correctly. Thank you for the link. I could use tech support for this cms right now.Author: huck77 Time: 4/7/2025 22:59
Exactly what Diana92 recommended is what we were all looking for, a serious company that offers 100% professional Drupal migration services, right? Seriously, thank you very much. I've been looking for a company like that for days and I can't believe I finally found it here thanks to you. You are the best Diana92. I love you very much. You should read the message I left you. I assure you that we will get along well and it will be the beginning of a great friendship. Believe me.Author: dimitri6 Time: 4/8/2025 00:01
I just saw this post, I'm shocked at how many comments there are in one place, I think it's great that everyone has joined together to start commenting on a chain in which everyone helps each other until they find the best answer and the best help, I find it extremely fascinating, seriously, I would like to contribute something on my part but the truth is that I don't have much to contribute sincerely more than what has already been said.
Welcome Firefly Open Source Community (https://bbs.t-firefly.com/)