EMC D-PST-DY-23を習う：100％の合格率を持つDell PowerStore Deploy 2023 Exam 試験 D-PST-DY-23オンライン試験急速な市場の発展に伴い、学習者が試験の準備に役立つD-PST-DY-23ガイド急流を販売する企業やWebサイトが増えています。あなたが以前に知っていたなら、当社の教材が学生やビジネスマンに関係なく候補者に非常に人気があることを見つけることは難しくありません。 D-PST-DY-23試験トレントの購入を歓迎します。古いsayingにもあるように、クライアントは神です！サービスが一番です！ D-PST-DY-23ガイドBraindumpsは、限られた時間の試験とオンラインエラー修正をシミュレートでき、24時間年中無休のサービスを提供しています。D-PST-DY-23試験Torrentは、試験を準備するための最良かつ賢明な選択です。
認定試験は、Dell Powerstore 2023ストレージソリューションのさまざまな分野で候補者の知識とスキルをテストする複数選択の質問で構成されています。この試験は、監督済みの環境で実施されており、候補者は試験に合格するために最低63％を獲得する必要があります。試験を正常に完了すると、候補者はEMC D-PST-DY-23認定を獲得します。 EMC Dell PowerStore Deploy 2023 Exam 認定 D-PST-DY-23 試験問題 (Q21-Q26):質問 # 21
Which IP network range is used by the PowerStore Discovery Network?
A. 128.221.1.249/25
B. 128.221.0.0/16
C. 169.254.0.0/16
D. 192.168.1.200/24
正解：C
質問 # 22
The wan connection between the production and DR sites has a low latency of <5 milliseconds.
Which firewall port is used by PowerStore to communicate between sites?
A. 0
B. 1
C. 2
D. 3
正解：C
解説：
PowerStore uses port 13337 for communication between sites in a replication setup. This port is required to enable data transfer and management communication over the WAN connection between the production and disaster recovery (DR) sites. The low latency condition (≥ 120 milliseconds) highlights the importance of maintaining efficient data transfer, and proper firewall configuration ensures PowerStore uses different ports for replication traffic based on the latency between the two sites. Since you have a low latency connection (< 5 milliseconds), PowerStore will use port 13333.
Here's a breakdown of the ports and their corresponding latency:
13333: Low latency (< 5 milliseconds) - This is the default setting.
13334: Low Medium latency (>= 5 and < 20 milliseconds) 1
13335: Medium latency (>= 20 and < 60 milliseconds)
13336: Medium High latency (>= 60 and < 120 milliseconds)
13337: High latency (>= 120 milliseconds)
It's important to configure your firewalls to allow traffic on the correct port to ensure successful replication between your production and DR sites.
質問 # 23
Which IP addresses are required when adding an appliance to the cluster?
A. Management and DNS
B. Management and Storage
C. Storage and NTP
D. DNS and NTP
正解：B
質問 # 24
What does setting the alert threshold to 0 (zero) do when configuring replication rules?
A. Generates an alert if the data saved during the RPO cycle exceeds 20% of the storage object capacity
B. Disables all alerts for any missed RPO cycles.
C. Generates an alert if the synchronization time exceeds the RPO.
D. Enables alerts if the RPO cycle was missed for three consecutive cycles.
正解：B
質問 # 25
An administrator is attempting to create a protection policy while creating an SMB share however the option is not available.
What is the reason?
A. The protection policy has been previously associated with a file system
B. The protection policy must be created before associating it with the file system
C. The protection policy is only available with file level retention enabled
D. The protection policy must be created before associating it with the volume resource