Firefly Open Source Community

Title: DeBrick FireWRT [Print This Page]
Author: mo_wie    Time: 10/16/2015 01:03
Title: DeBrick FireWRT
Hey there, I would apprieciate some help on my bricked FirWRT:

Recently I bricked my FireWRT after trying to flash OpenWRT (openwrt-ramips-mt7621-firewrt-squashfs-sysupgrade.bin) from here:
http://wiki.openwrt.org/toh/firefly/firewrt

I could re-flash the original firmware

2015-05-07-firewrt-mt7621-openwrt-trunk.bin or
2015-06-02-firewrt-mt7621-openwrt-trunk.bin

from here:
http://en.t-firefly.com/en/firelink/firewrt/download/

as described in the official guide (HTTP download):
http://wiki.t-firefly.com/index. ... ad_OpenWrt_Firmware


The problem is, that the device is not coming up but running a boot loop.
The serial debug console looks like this:

-----------------------------------------------------------------------------
  1. U-Boot 1.1.3 (May  7 2015 - 10:40:34)

  3. Board: Ralink APSoC DRAM:  448 MB
  4. relocate_code Pointer at: 9bfb4000

  6. Config XHCI 40M PLL
  7. ***********************
  8. Watchdog Reset Occurred
  9. ***********************
  10. flash manufacture id: ef, device id 40 18
  11. find flash: W25Q128BV
  12. ============================================
  13. FireWRT UBoot Version: 1.0
  14. --------------------------------------------
  15. ASIC MT7621A DualCore (MAC to MT7530 Mode)
  16. DRAM_CONF_FROM: Auto-Detection
  17. DRAM_TYPE: DDR3
  18. DRAM bus: 16 bit
  19. Xtal Mode=3 OCP Ratio=1/4
  20. Flash component: SPI Flash
  21. Date:May  7 2015  Time:10:40:34
  22. ============================================
  23. icache: sets:256, ways:4, linesz:32 ,total:32768
  24. dcache: sets:256, ways:4, linesz:32 ,total:32768
  25. set LAN/WAN WLL


  28. .-------.             __                __
  29. |  _____/            |  |              |  | __
  30. |  __/__ .----..----.|  |    __ .-----.|  |/  /
  31. |  | |  ||   _|| -__||  |__ |  ||     ||     <
  32. |__| |__||__|  |____||_____||__||__|__||__|\__\
  33. --------------------------------------------------
  34.                   FIREFLY Team
  35.           Full of enthusiasm and dream
  36.            <fl.service@t-firely.com>
  37. --------------------------------------------------

  39. Please choose the operation:
  40.    1: Load system code to SDRAM via TFTP.
  41.    2: Load system code then write to Flash via TFTP.
  42.    3: Boot system code via Flash (default).
  43.    4: Entr boot command line interface.
  44.    5: Load system code then write to Flash via Httpd.
  45.    7: Load Boot Loader code then write to Flash via Serial.
  46.    9: Load Boot Loader code then write to Flash via TFTP.
  47. 0
  48.    
  49. 3: System Boot system code via Flash.
  50. ## Booting image at bfc50000 ...
  51.    Image Name:   MIPS OpenWrt Linux-3.18.11
  52.    Image Type:   MIPS Linux Kernel Image (lzma compressed)
  53.    Data Size:    1194098 Bytes =  1.1 MB
  54.    Load Address: 80001000
  55.    Entry Point:  80001000
  56.    Verifying Checksum ... OK
  57.    Uncompressing Kernel Image ... OK
  58. No initrd
  59. ## Transferring control to Linux (at address 80001000) ...
  60. ## Giving linux memsize in MB, 448

  62. Starting kernel ...

  64. [    0.000000] Linux version 3.18.11 (wengbj@tchip-server) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r45583) ) #8 SMP Tue Jun 2 16:56:47 CST 2015
  65. [    0.000000] SoC Type: Mediatek MT7621 ver:1 eco:3
  66. [    0.000000] bootconsole [early0] enabled
  67. [    0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
  68. [    0.000000] MIPS: machine is Firefly FireWRT
  69. [    0.000000] Determined physical RAM map:
  70. [    0.000000]  memory: 10000000 @ 00000000 (usable)
  71. [    0.000000] Initrd not found or empty - disabling initrd
  72. [    0.000000] Zone ranges:
  73. [    0.000000]   Normal   [mem 0x00000000-0x0fffffff]
  74. [    0.000000]   HighMem  empty
  75. [    0.000000] Movable zone start for each node
  76. [    0.000000] Early memory node ranges
  77. [    0.000000]   node   0: [mem 0x00000000-0x0fffffff]
  78. [    0.000000] Initmem setup node 0 [mem 0x00000000-0x0fffffff]
  79. [    0.000000] Detected 3 available secondary CPU(s)
  80. [    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
  81. [    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
  82. [    0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
  83. [    0.000000] PERCPU: Embedded 9 pages/cpu @8120d000 s5696 r8192 d22976 u36864
  84. [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
  85. [    0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
  86. [    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
  87. [    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
  88. [    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
  89. [    0.000000] Writing ErrCtl register=00001031
  90. [    0.000000] Readback ErrCtl register=00001031
  91. [    0.000000] Memory: 255912K/262144K available (2688K kernel code, 144K rwdata, 520K rodata, 156K init, 224K bss, 6232K reserved, 0K highmem)
  92. [    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
  93. [    0.000000] Hierarchical RCU implementation.
  94. [    0.000000] NR_IRQS:256
  95. [    0.000000] gic: revision 3.0
  96. [    0.000000] CPU Clock: 880MHz
  97. [    0.000000] Calibrating delay loop... 577.53 BogoMIPS (lpj=2887680)
  98. [    0.060000] pid_max: default: 32768 minimum: 301
  99. [    0.070000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
  100. [    0.080000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
  101. [    0.090000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
  102. [    0.090000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
  103. [    0.090000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
  104. [    0.090000] CPU1 revision is: 0001992f (MIPS 1004Kc)
  105. [    0.200000] Synchronize counters for CPU 1: done.
  106. [    0.210000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
  107. [    0.210000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
  108. [    0.210000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
  109. [    0.210000] CPU2 revision is: 0001992f (MIPS 1004Kc)
  110. [    0.310000] Synchronize counters for CPU 2: done.
  111. [    0.330000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
  112. [    0.330000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
  113. [    0.330000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
  114. [    0.330000] CPU3 revision is: 0001992f (MIPS 1004Kc)
  115. [    0.430000] Synchronize counters for CPU 3: done.
  116. [    0.450000] Brought up 4 CPUs
  117. [    0.450000] pinctrl core: initialized pinctrl subsystem
  118. [    0.460000] NET: Registered protocol family 16
  119. [    0.470000] pull PCIe RST: RALINK_RSTCTRL = 6000000
  120. [    0.770000] release PCIe RST: RALINK_RSTCTRL = 7000000
  121. [    0.780000] ***** Xtal 40MHz *****
  122. [    0.780000] release PCIe RST: RALINK_RSTCTRL = 7000000
  123. [    0.790000] Port 0 N_FTS = 1b105000
  124. [    0.790000] Port 1 N_FTS = 1b105000
  125. [    0.800000] Port 2 N_FTS = 1b105000
  126. [    1.940000]  -> 21007f2
  127. [    1.940000] PCIE0 enabled
  128. [    1.950000] PCIE1 enabled
  129. [    1.950000] PCIE2 enabled
  130. [    1.960000] PCI host bridge /pcie@1e140000 ranges:
  131. [    1.970000]  MEM 0x0000000060000000..0x000000006fffffff
  132. [    1.980000]   IO 0x000000001e160000..0x000000001e16ffff
  133. [    2.020000] mt7621_gpio 1e000600.gpio: registering 32 gpios
  134. [    2.030000] mt7621_gpio 1e000600.gpio: registering 32 gpios
  135. [    2.040000] mt7621_gpio 1e000600.gpio: registering 32 gpios
  136. [    2.050000] PCI host bridge to bus 0000:00
  137. [    2.060000] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
  138. [    2.080000] pci_bus 0000:00: root bus resource [io  0xffffffff]
  139. [    2.090000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
  140. [    2.110000] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
  141. [    2.130000] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
  142. [    2.150000] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
  143. [    2.160000] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
  144. [    2.180000] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
  145. [    2.190000] pci 0000:00:02.0: BAR 0: no space for [mem size 0x80000000]
  146. [    2.210000] pci 0000:00:02.0: BAR 0: failed to assign [mem size 0x80000000]
  147. [    2.220000] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
  148. [    2.240000] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref]
  149. [    2.250000] pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff]
  150. [    2.270000] pci 0000:00:01.0: BAR 9: assigned [mem 0x60300000-0x603fffff pref]
  151. [    2.290000] pci 0000:00:02.0: BAR 8: assigned [mem 0x60400000-0x604fffff]
  152. [    2.300000] pci 0000:00:02.0: BAR 9: assigned [mem 0x60500000-0x605fffff pref]
  153. [    2.320000] pci 0000:00:00.0: BAR 1: assigned [mem 0x60600000-0x6060ffff]
  154. [    2.330000] pci 0000:00:01.0: BAR 1: assigned [mem 0x60610000-0x6061ffff]
  155. [    2.350000] pci 0000:00:02.0: BAR 1: assigned [mem 0x60620000-0x6062ffff]
  156. [    2.360000] pci 0000:00:02.0: BAR 7: no space for [io  size 0x1000]
  157. [    2.380000] pci 0000:00:02.0: BAR 7: failed to assign [io  size 0x1000]
  158. [    2.390000] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit]
  159. [    2.410000] pci 0000:01:00.0: BAR 6: assigned [mem 0x60100000-0x6010ffff pref]
  160. [    2.430000] pci 0000:00:00.0: PCI bridge to [bus 01]
  161. [    2.440000] pci 0000:00:00.0:   bridge window [mem 0x60000000-0x600fffff]
  162. [    2.450000] pci 0000:00:00.0:   bridge window [mem 0x60100000-0x601fffff pref]
  163. [    2.470000] pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff 64bit]
  164. [    2.490000] pci 0000:02:00.0: BAR 6: assigned [mem 0x60300000-0x6030ffff pref]
  165. [    2.500000] pci 0000:00:01.0: PCI bridge to [bus 02]
  166. [    2.510000] pci 0000:00:01.0:   bridge window [mem 0x60200000-0x602fffff]
  167. [    2.530000] pci 0000:00:01.0:   bridge window [mem 0x60300000-0x603fffff pref]
  168. [    2.540000] pci 0000:03:00.0: BAR 6: assigned [mem 0x60500000-0x6050ffff pref]
  169. [    2.560000] pci 0000:03:00.0: BAR 5: assigned [mem 0x60400000-0x604001ff]
  170. [    2.580000] pci 0000:03:00.0: BAR 4: no space for [io  size 0x0020]
  171. [    2.590000] pci 0000:03:00.0: BAR 4: failed to assign [io  size 0x0020]
  172. [    2.600000] pci 0000:03:00.0: BAR 0: no space for [io  size 0x0008]
  173. [    2.620000] pci 0000:03:00.0: BAR 0: failed to assign [io  size 0x0008]
  174. [    2.630000] pci 0000:03:00.0: BAR 2: no space for [io  size 0x0008]
  175. [    2.650000] pci 0000:03:00.0: BAR 2: failed to assign [io  size 0x0008]
  176. [    2.660000] pci 0000:03:00.0: BAR 1: no space for [io  size 0x0004]
  177. [    2.680000] pci 0000:03:00.0: BAR 1: failed to assign [io  size 0x0004]
  178. [    2.690000] pci 0000:03:00.0: BAR 3: no space for [io  size 0x0004]
  179. [    2.710000] pci 0000:03:00.0: BAR 3: failed to assign [io  size 0x0004]
  180. [    2.720000] pci 0000:00:02.0: PCI bridge to [bus 03]
  181. [    2.730000] pci 0000:00:02.0:   bridge window [mem 0x60400000-0x604fffff]
  182. [    2.750000] pci 0000:00:02.0:   bridge window [mem 0x60500000-0x605fffff pref]
  183. [    2.760000] BAR0 at slot 0 = 0
  184. [    2.770000] bus=0x0, slot = 0x0
  185. [    2.780000] BAR0 at slot 1 = 0
  186. [    2.780000] bus=0x0, slot = 0x1
  187. [    2.790000] BAR0 at slot 2 = 0
  188. [    2.800000] bus=0x0, slot = 0x2
  189. [    2.810000] bus=0x1, slot = 0x0, irq=0xff
  190. [    2.810000] bus=0x2, slot = 0x1, irq=0xff
  191. [    2.820000] bus=0x3, slot = 0x2, irq=0x0
  192. [    2.830000] Switched to clocksource MIPS
  193. [    2.850000] NET: Registered protocol family 2
  194. [    2.860000] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
  195. [    2.870000] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
  196. [    2.890000] TCP: Hash tables configured (established 2048 bind 2048)
  197. [    2.900000] TCP: reno registered
  198. [    2.910000] UDP hash table entries: 256 (order: 1, 8192 bytes)
  199. [    2.920000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
  200. [    2.940000] NET: Registered protocol family 1
  201. [    2.950000] futex hash table entries: 1024 (order: 4, 65536 bytes)
  202. [    2.970000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  203. [    2.980000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
  204. [    3.000000] msgmni has been set to 499
  205. [    3.010000] io scheduler noop registered
  206. [    3.020000] io scheduler deadline registered (default)
  207. [    3.030000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
  208. [    3.050000] console [ttyS0] disabled
  209. [    3.060000] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 34, base_baud = 3125000) is a 16550A
  210. [    3.080000] console [ttyS0] enabled
  211. [    3.080000] console [ttyS0] enabled
  212. [    3.090000] bootconsole [early0] disabled
  213. [    3.090000] bootconsole [early0] disabled
  214. [    3.110000] m25p80 spi32766.0: w25q128 (16384 Kbytes)
  215. [    3.120000] m25p80 spi32766.0: using chunked io
  216. [    3.130000] 4 ofpart partitions found on MTD device spi32766.0
  217. [    3.150000] Creating 4 MTD partitions on "spi32766.0":
  218. [    3.160000] 0x000000000000-0x000000030000 : "u-boot"
  219. [    3.170000] 0x000000030000-0x000000040000 : "u-boot-env"
  220. [    3.180000] 0x000000040000-0x000000050000 : "factory"
  221. [    3.200000] 0x000000050000-0x000001000000 : "firmware"
  222. [    3.300000] random: nonblocking pool is initialized
  223. [    3.320000] 2 uimage-fw partitions found on MTD device firmware
  224. [    3.340000] 0x000000050000-0x0000001738b2 : "kernel"
  225. [    3.350000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
  226. [    3.380000] 0x0000001738b2-0x000001000000 : "rootfs"
  227. [    3.390000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
  228. [    3.420000] mtd: device 5 (rootfs) set to be root filesystem
  229. [    3.430000] 1 squashfs-split partitions found on MTD device rootfs
  230. [    3.440000] 0x000000640000-0x000001000000 : "rootfs_data"
  231. [    3.460000] netif_napi_add() called with weight 128 on device eth%d
  232. [    3.480000] change HW-TRAP to 0x17ccf
  233. [    3.490000] libphy: mdio: probed
  234. [    3.510000] ralink_soc_eth 1e100000.ethernet: loaded mt7530 driver
  235. [    3.530000] ralink_soc_eth 1e100000.ethernet eth0: ralink at 0xbe100000, irq 11
  236. [    3.540000] mt7621_wdt 1e000100.wdt: Initialized
  237. [    3.560000] TCP: cubic registered
  238. [    3.560000] NET: Registered protocol family 17
  239. [    3.570000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
  240. [    3.600000] 8021q: 802.1Q VLAN Support v1.8
  241. [    3.620000] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
  242. [    3.640000] Freeing unused kernel memory: 156K (80349000 - 80370000)
  243. [    5.420000] init: failed to symlink /tmp -> /var
  244. [    5.430000] init: Console is alive
  245. [    5.440000] init: - watchdog -
  246. [    7.870000] ralink_soc_eth 1e100000.ethernet eth0: port 3 link up
  247. [    8.950000] usbcore: registered new interface driver usbfs
  248. [    8.960000] usbcore: registered new interface driver hub
  249. [    8.970000] usbcore: registered new device driver usb
  250. [    8.990000] exFAT: Version 1.2.9
  251. [    9.030000] SCSI subsystem initialized
  252. [    9.060000] ahci 0000:03:00.0: SSS flag set, parallel bus scan disabled
  253. [    9.070000] ahci 0000:03:00.0: AHCI 0001.0200 32 slots 2 ports 6 Gbps 0x3 impl SATA mode
  254. [    9.090000] ahci 0000:03:00.0: flags: 64bit ncq sntf stag led clo pmp pio slum part ccc sxs
  255. [    9.110000] scsi host0: ahci
  256. [    9.120000] scsi host1: ahci
  257. [    9.120000] ata1: SATA max UDMA/133 abar m512@0x60400000 port 0x60400100 irq 33
  258. [    9.140000] ata2: SATA max UDMA/133 abar m512@0x60400000 port 0x60400180 irq 33
  259. [    9.510000] ata1: SATA link down (SStatus 0 SControl 300)
  260. [    9.870000] ata2: SATA link down (SStatus 0 SControl 300)
  261. [    9.900000] FM_OUT value: u4FmOut = 0(0x00000000)
  262. [    9.930000] FM_OUT value: u4FmOut = 0(0x00000000)
  263. [    9.960000] FM_OUT value: u4FmOut = 0(0x00000000)
  264. [    9.990000] FM_OUT value: u4FmOut = 0(0x00000000)
  265. [   10.020000] FM_OUT value: u4FmOut = 0(0x00000000)
  266. [   10.050000] FM_OUT value: u4FmOut = 0(0x00000000)
  267. [   10.080000] FM_OUT value: u4FmOut = 0(0x00000000)
  268. [   10.110000] FM_OUT value: u4FmOut = 0(0x00000000)
  269. [   10.140000] FM_OUT value: u4FmOut = 0(0x00000000)
  270. [   10.170000] FM_OUT value: u4FmOut = 0(0x00000000)
  271. [   10.240000] FM_OUT value: u4FmOut = 0(0x00000000)
  272. [   10.270000] FM_OUT value: u4FmOut = 0(0x00000000)
  273. [   10.300000] FM_OUT value: u4FmOut = 0(0x00000000)
  274. [   10.330000] FM_OUT value: u4FmOut = 0(0x00000000)
  275. [   10.360000] FM_OUT value: u4FmOut = 0(0x00000000)
  276. [   10.390000] FM_OUT value: u4FmOut = 0(0x00000000)
  277. [   10.420000] FM_OUT value: u4FmOut = 0(0x00000000)
  278. [   10.450000] FM_OUT value: u4FmOut = 0(0x00000000)
  279. [   10.480000] FM_OUT value: u4FmOut = 0(0x00000000)
  280. [   10.510000] FM_OUT value: u4FmOut = 0(0x00000000)
  281. [   10.670000] xhci-hcd xhci-hcd: xHCI Host Controller
  282. [   10.680000] xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 1
  283. [   10.700000] xhci-hcd xhci-hcd: irq 30, io mem 0x1e1c0000
  284. [   10.710000] hub 1-0:1.0: USB hub found
  285. [   10.720000] hub 1-0:1.0: 2 ports detected
  286. [   10.730000] xhci-hcd xhci-hcd: xHCI Host Controller
  287. [   10.740000] xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 2
  288. [   10.760000] hub 2-0:1.0: USB hub found
  289. [   10.760000] hub 2-0:1.0: 1 port detected
  290. [   10.780000] MTK MSDC device init.
  291. [   10.830000] msdc0 -> set mclk to 0!!! <- msdc_set_mclk() : L<641> PID<kworker/u8:1><0x17>
  292. [   10.830000] mtk-sd: MediaTek MT6575 MSDC Driver
  293. [   10.830000] sdhci: Secure Digital Host Controller Interface driver
  294. [   10.830000] sdhci: Copyright(c) Pierre Ossman
  295. [   10.830000] sdhci-pltfm: SDHCI platform and OF driver helper
  296. [   10.830000] usbcore: registered new interface driver usb-storage
  297. [   11.440000] init: - preinit -
  298. Press the [f] key and hit [enter] to enter failsafe mode
  299. Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
  300. [   15.180000] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
  301. [   15.210000] procd: - early -
  302. [   15.220000] procd: - watchdog -
  303. [   16.060000] procd: - ubus -
  304. [   17.070000] procd: - init -
  305. Please press Enter to activate this console.
  306. [   17.980000] NET: Registered protocol family 10
  307. [   18.000000] ntfs: driver 2.1.31 [Flags: R/O MODULE].
  308. [   18.020000] ip6_tables: (C) 2000-2006 Netfilter Core Team
  309. [   18.050000] hidraw: raw HID events driver (C) Jiri Kosina
  310. [   18.070000] fuse init (API version 7.23)
  311. [   19.070000]
  312. [   19.070000]
  313. [   19.070000] === pAd = c0781000, size = 1980536 ===
  314. [   19.070000]
  315. [   19.090000] <-- RTMPAllocTxRxRingMemory, Status=0
  316. [   19.100000] <-- RTMPAllocAdapterBlock, Status=0
  317. [   19.110000] device_id =0x7662
Copy the code


-----------------------------------------------------------------------------

This is reproducable and always happening around second 18/19 after the following two lines:

<-- RTMPAllocAdapterBlock, Status=0
<-- RTMPAllocTxRxRingMemory, Status=0




I can enter boot command line interface, tftp and http-download and failsafe-mode via serial debug console.
The device is not responding to "ping" in any mode. The only mode where it responds is http-download. Telnet doesnt seem to work. TFTP wont accept any files.

In failsafe mode Im able to do "mount_root" and "firstboot":


  2. root@(none):/# mount_root
  3. [   90.950000] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
  4. root@(none):/# firstboot -y
  5. [   95.170000] jffs2reset: /dev/mtdblock6 is not mounted
  6. [   95.180000] jffs2reset: /dev/mtdblock6 will be erased on next mount
Copy the code




Is there any way to revive this device? I would be happy to bring in any details needed...

Thanks for your efforts _ moritz
Author: ericmil135    Time: 1/11/2026 15:23
CertShikenは、最新のテクノロジーに遅れずについていき、コンテンツだけでなくディスプレイでも試験の質問と回答にそれらを適用しようとしています。それが、私たちの合格率が98％から100％と高い理由です。データはユニークで、このキャリアに特有です。 Databricks-Certified-Professional-Data-Engineer勉強のトレントを使用すると、レジャーの学習体験を楽しむことができ、Databricks-Certified-Professional-Data-Engineer試験に合格すると確実に合格します。 Databricks-Certified-Professional-Data-Engineer準備資料の内容については、専門家によって簡素化され、ディスプレイは効果的に設計されています。試して楽しんでください！
Author: sophier641    Time: 1/15/2026 13:06
That article was a real treasure trove of knowledge. Get your hands on the FCSS_SDW_AR-7.6 valid exam sample online test that helped me achieve a promotion and salary increase, and it’s available for free today. I hope you hit your career goals soon!
Author: tomwalk204    Time: 1/16/2026 13:21
Thank you for your article, it left an unforgettable impression on me. NCP-AI reliable exam discount voucher is free and offers rich content to help you on your educational journey.
Author: iantayl421    Time: before yesterday 15:04
Your article has made a lasting impression, thank you! Here’s the Latest test N16291GC10 sample questions test I took to earn my promotion and raise, now free for you today. Best of luck in your professional journey!
Author: rickgre625    Time: yesterday 23:22
What an enlightening and motivating read, thank you for sharing! Free Valid real PT-AM-CPE exam exam questions—good luck to everyone!



Welcome Firefly Open Source Community (https://bbs.t-firefly.com/) Powered by Discuz! X3.1