SPI AIO-3128C

JuandeDios

Dear colleagues, I'm building a kernel driver to a device. This device has SPI interface.  I sent data by SPI with the last fireprime model but in this moment I can't send anything by SPI with  AIO board. DTS file are diferent and I don't have schematics to check conections. I have some questions.

1 Which dts file do I have to change? aio-3128c.dts or rk3128-fireprime-aio.dts
2. What do i have to do in this code to use SPI interface?

&spi0 {
    status = "okay";
    max-freq = <48000000>;

    dac0: dh2228@00 {
              status = "disabled";
              compatible = "rohm,dh2228fv";
              reg = <00>;
              spi-max-frequency = <100000>;
          };

    spi_wk2xxx: spi_wk2xxx@00{
                status = "okay";
                compatible = "firefly,spi-wk2xxx";
                reg = <0x00>;
                spi-max-frequency = <10000000>;
                reset-gpio = <&gpio3 GPIO_D3 GPIO_ACTIVE_HIGH>;
                irq-gpio = <&gpio1 GPIO_B4 IRQ_TYPE_EDGE_FALLING>;
                cs-gpio = <&gpio1 GPIO_B3 GPIO_ACTIVE_HIGH>;
                pwr-en-gpio = <&gpio0 GPIO_B4 GPIO_ACTIVE_HIGH>;
            };
};


Any suggestion? Thank you very much.

leung先森

need to disabled spi_wk2xxx

JuandeDios

The problem was solved. I changed in 312x.dtsi pinctrl-0 = <&spi0_txd_mux0 &spi0_rxd_mux0 &spi0_clk_mux0 &spi0_cs0_mux0 &spi0_cs1_mux0>; to pinctrl-0 = <&spi0_txd_mux2 &spi0_rxd_mux2 &spi0_clk_mux2 &spi0_cs0_mux2>; and it's working.

        spi0: spi@20074000 {
                compatible = "rockchip,rockchip-spi";
                reg = <0x20074000 0x1000>;
                interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
                #address-cells = <1>;
                #size-cells = <0>;
                pinctrl-names = "default";
                //pinctrl-0 = <&spi0_txd_mux0 &spi0_rxd_mux0 &spi0_clk_mux0 &spi0_cs0_mux0 &spi0_cs1_mux0>;
                //pinctrl-0 = <&spi0_txd_mux1 &spi0_rxd_mux1 &spi0_clk_mux1 &spi0_cs0_mux1 &spi0_cs1_mux1>;
                pinctrl-0 = <&spi0_txd_mux2 &spi0_rxd_mux2 &spi0_clk_mux2 &spi0_cs0_mux2>;
                rockchip,spi-src-clk = <0>;
                num-cs = <2>;
                clocks =<&clk_spi0>, <&clk_gates7 12>;
                clock-names = "spi","pclk_spi0";
                dmas = <&pdma 8>, <&pdma 9>;
                #dma-cells = <2>;
                dma-names = "tx", "rx";
                status = "disabled";
        };

Thanks a lot.

iangree106

JPTestKingにIT業界のエリートのグループがあって、彼達は自分の経験と専門知識を使ってCompTIA 220-1102J認証試験に参加する方に対して問題集を研究続けています。君が後悔しないようにもっと少ないお金を使って大きな良い成果を取得するためにJPTestKingを選択してください。JPTestKingはまた一年間に無料なサービスを更新いたします。

mikebla462

What a motivating article, thanks for sharing it with us! The New AICP learning materials content is of high value, and it’s free to access.