RK3399 CPU on custom hardware. Strange kernel output

marijnr

Hi,

I'm trying to compile an RK3399 image as described in http://wiki.t-firefly.com/ROC-RK ... ompile_firmware.htm and http://opensource.rock-chips.com/wiki_Linux_user_guide. We have created custom hardware using the RK3399 CPU. When starting up a default generated kernel, it will stop when trying to find the serial ports. The last lines it prints is:

1. [    0.900624] dma-pl330 ff6d0000.dma-controller: Loaded driver for PL330 DMAC-241330
   
2. [    0.901293] dma-pl330 ff6d0000.dma-controller:       DBUFF-32x8bytes Num_Chans-6 Num_Peri-12 Num_Events-12
   
3. [    0.903508] dma-pl330 ff6e0000.dma-controller: Loaded driver for PL330 DMAC-241330
   
4. [    0.904188] dma-pl330 ff6e0000.dma-controller:       DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16
   
5. [    0.906020] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
   
6. [    0.908085] ff180000.serial: ttyS0 at MMIO 0xff180000 (irq = 36, base_baud = 1500000) is a 16550A
   
7. [    0.909184] rockchip-pinctrl pinctrl: pin gpio4-19 already requested by fiq-debugger; cannot claim for ff1a0000.smria▒▒
   
8. 
   
9.                                                                         
   
10.                                                   [  
    
11. 0(0.▒̰140],vocml▒ip-pko▒▒l`pyngu▒l▒▒py~-37s▒▒ff1y<63̗▒▒▒yy|-&w▒غ▒▒▒mr:▒`08<>/;▒̳▒▒▒▒▒▒▒sxy|?~o▒▒▒▒▒▒py▒▒▒|_?▒|x~'▒▒▒▒▒▒▒x~/▒▒▒▒▒~▒▒▒▒}??/▒▒▒▒▒?▒▒▒▒▒▒▒▒▒|~??▒▒▒▒▒▒▒▒▒▒|▒▒▒▒▒▒▒▒~~~?▒▒▒▒▒▒▒▒▒▒▒▒~▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒

Copy the code

The characters that aren't correct (that garbled mess) are never the same. But what follows are always some random ASCII characters.
When I then disable some things of FIQ, the kernel won't start.

I tried to see what would happen if I told the kernel to limit the amount of ports for the serial 8250 driver to zero, and I get the following result:

1. [    0.905219] dma-pl330 ff6d0000.dma-controller: Loaded driver for PL330 DMAC-241330
   
2. [    0.905889] dma-pl330 ff6d0000.dma-controller:       DBUFF-32x8bytes Num_Chans-6 Num_Peri-12 Num_Events-12
   
3. [    0.908140] dma-pl330 ff6e0000.dma-controller: Loaded driver for PL330 DMAC-241330
   
4. [    0.908821] dma-pl330 ff6e0000.dma-controller:       DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16
   
5. [    0.911054] dw-apb-uart: probe of ff180000.serial failed with error -28
   
6. [    0.911728] rockchip-pinctrl pinctrl: pin gpio4-19 already requested by fiq-debugger; cannot claim for ff1a0000.serial
   
7. [    0.912680] rockchip-pinctrl pinctrl: pin-147 (ff1a0000.serial) status -22
   
8. [    0.913296] rockchip-pinctrl pinctrl: could not request pin 147 (gpio4-19) from group uart2c-xfer  on device rockchip-pinctrl
   
9. [    0.913293] dw-apb-uart ff1a0000.serial: Error applying setting, reverse things back
   
10. [!▒▒▒p>=75▒0▒] /c▒▒-▒▒▒t:,vs▒l▒▒▒fv9m6̟8gs▒ض▒▒▒y|}n#▒▒▒▒`uzzo

Copy the code

For some reason, it got further into the kernel without corrupting my serial output.
I then saw what happend if I disabled everything from my serial driver, and now, it will skip the part that corrupted my output (like it should), but it got corrupted a few lines later:

1. [ 0.900572] dma-pl330 ff6d0000.dma-controller: Loaded driver for PL330 DMAC-241330
   
2. [ 0.901242] dma-pl330 ff6d0000.dma-controller: DBUFF-32x8bytes Num_Chans-6 Num_Peri-12 Num_Events-12
   
3. [ 0.903530] dma-pl330 ff6e0000.dma-controller: Loaded driver for PL330 DMAC-241330
   
4. [ 0.904199] dma-pl330 ff6e0000.dma-controller: DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16
   
5. [ 0.906253] [drm] Initialized drm 1.1.0 20060810
   
6. [
   
7. 0.909842] rockchip-▒r}0lmws▒▒y▒▒ubsvg۝▒▒▒c
   
8. y{,dksر▒▒d-▒Р▒▒▒▒yyx8=>]<ooooo▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒|▒▒~|}~~>?????▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒

Copy the code

This is where I'm stuck. At first I thought the FIQ debugger was the problem, but with that last image, I have no idea where to look.


THE FULL LOGS WITH THE DEFAULT IMAGE (FIQ on, UART PORTS 5)

1. DDR Version 1.08 20170320
   
2. In
   
3. Channel 0: DDR3, 800MHz
   
4. Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
   
5. Channel 1: DDR3, 800MHz
   
6. Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
   
7. 256B stride
   
8. ch 0 ddrconfig = 0x101, ddrsize = 0x20
   
9. ch 1 ddrconfig = 0x101, ddrsize = 0x20
   
10. pmugrf_os_reg[2] = 0x32817281, stride = 0x9
    
11. OUT
    
12. Boot1: 2017-04-07, version: 1.06
    
13. CPUId = 0x0
    
14. ChipType = 0x10, 1825
    
15. SdmmcInit=2 0
    
16. BootCapSize=100000
    
17. UserCapSize=7456MB
    
18. FwPartOffset=2000 , 100000
    
19. SdmmcInit=0 0
    
20. BootCapSize=0
    
21. UserCapSize=30436MB
    
22. FwPartOffset=2000 , 0
    
23. StorageInit ok = 311038
    
24. LoadTrustBL
    
25. No find bl30.bin
    
26. RunBL31 0x10000
    
27. NOTICE:  BL31: v1.3(debug):65aa5ce
    
28. NOTICE:  BL31: Built : 10:47:37, Jun 19 2018
    
29. NOTICE:  BL31: Rockchip release version: v1.1
    
30. INFO:    GICv3 with legacy support detected. ARM GICV3 driver initialized in EL3
    
31. INFO:    Using opteed sec cpu_context!
    
32. INFO:    boot cpu mask: 0
    
33. INFO:    plat_rockchip_pmu_init(1151): pd status 3e
    
34. INFO:    BL31: Initializing runtime services
    
35. INFO:    BL31: Initializing BL32
    
36. INF [0x0] TEE-CORE:init_primary_helper:337: Initializing (1.1.0-170-gc4654a6 #16 Wed May 30 08:54:30 UTC 2018 aarch64)
    
37. 
    
38. INF [0x0] TEE-CORE:init_primary_helper:338: Release version: 1.2
    
39. 
    
40. INF [0x0] TEE-CORE:init_teecore:83: teecore inits done
    
41. INFO:    BL31: Preparing for EL3 exit to normal world
    
42. INFO:    Entry point address = 0x200000
    
43. INFO:    SPSR = 0x3c9
    
44. 
    
45. 
    
46. U-Boot 2017.09-01874-ga60b58c (Aug 16 2018 - 15:49:09 +0200)
    
47. 
    
48. Model: Firefly-RK3399 Board
    
49. DRAM:  2 GiB
    
50. Relocation Offset is: 7fd15000
    
51. rk8xx_read: read reg 0x17 failed, ret=-121
    
52. MMC:   dwmmc@fe320000: 1, sdhci@fe330000: 0
    
53. invalid parameter
    
54. *** Warning - bad CRC, using default environment
    
55. 
    
56. In:    serial@ff1a0000
    
57. Out:   serial@ff1a0000
    
58. Err:   serial@ff1a0000
    
59. Model: Firefly-RK3399 Board
    
60. switch to partitions #0, OK
    
61. mmc1 is current device
    
62. do_rkimg_test found IDB in SDcard
    
63. Boot from SDcard
    
64. get part misc fail -1
    
65. Net:   eth0: ethernet@fe300000
    
66. Hit any key to stop autoboot:  0
    
67. android_bootloader_boot_flow Could not find misc partition
    
68. get part misc fail -1
    
69. ANDROID: reboot reason: "(none)"
    
70. ** Invalid Android Image header **
    
71. android_bootloader_boot_flow boot part load fail
    
72. Android boot failed, error -1.
    
73. get part misc fail -1
    
74. =Booting Rockchip format image=
    
75. boot_rockchip_image kernel or boot part info error
    
76. switch to partitions #0, OK
    
77. mmc1 is current device
    
78. Scanning mmc 1:4...
    
79. Found /extlinux/extlinux.conf
    
80. Retrieving file: /extlinux/extlinux.conf
    
81. reading /extlinux/extlinux.conf
    
82. 214 bytes read in 3 ms (69.3 KiB/s)
    
83. 1:      kernel-4.4
    
84. Retrieving file: /Image
    
85. reading /Image
    
86. 17936392 bytes read in 752 ms (22.7 MiB/s)
    
87. append:
    
88. earlyprintk console=ttyFIQ0,1500000n8 rw
    
89. root=PARTUUID=B921B045-1DF0-41C3-AF44-4C6F280D3FAE rootfstype=ext4
    
90. init=/sbin/init rootwait
    
91. Retrieving file: /rk3399-firefly-linux.dtb
    
92. reading /rk3399-firefly-linux.dtb
    
93. 75364 bytes read in 7 ms (10.3 MiB/s)
    
94. ## Flattened Device Tree blob at 01f00000
    
95.    Booting using the fdt blob at 0x1f00000
    
96.    Loading Device Tree to 00000000081ea000, end 00000000081ff663 ... OK
    
97. Adding bank: start=0x00200000, size=0x08200000
    
98. Adding bank: start=0x0a200000, size=0x75e00000
    
99. 
    
100. Starting kernel ...
     
101. 
     
102. 
     
103. [    0.000000] Booting Linux on physical CPU 0x0
     
104. [    0.000000] Initializing cgroup subsys cpuset
     
105. [    0.000000] Initializing cgroup subsys cpu
     
106. [    0.000000] Initializing cgroup subsys cpuacct
     
107. [
     
108.    0.000000] Linux version 4.4.114 (test@test-VirtualBox) (gcc version
     
109. 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.9) ) #37 SMP Wed Sep
     
110. 19 07:57:22 CEST 2018
     
111. [    0.000000] Boot CPU: AArch64 Processor [410fd034]
     
112. [    0.000000] Reserved memory: failed to reserve memory for node 'drm-logo@00000000': base 0x0000000000000000, size 0 MiB
     
113. [    0.000000] psci: probing for conduit method from DT.
     
114. [    0.000000] psci: PSCIv1.0 detected in firmware.
     
115. [    0.000000] psci: Using standard PSCI v0.2 function IDs
     
116. [    0.000000] psci: Trusted OS migration not required
     
117. [    0.000000] PERCPU: Embedded 21 pages/cpu @ffffffc07fef6000 s45800 r8192 d32024 u86016
     
118. [    0.000000] Detected VIPT I-cache on CPU0
     
119. [    0.000000] CPU features: enabling workaround for ARM erratum 845719
     
120. [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 507912
     
121. [
     
122.    0.000000] Kernel command line: earlyprintk console=ttyFIQ0,1500000n8
     
123. rw root=PARTUUID=B921B045-1DF0-41C3-AF44-4C6F280D3FAE rootfstype=ext4
     
124. init=/sbin/init rootwait
     
125. [    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
     
126. [    0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
     
127. [    0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
     
128. [    0.000000] software IO TLB [mem 0x79a00000-0x7da00000] (64MB) mapped at [ffffffc079a00000-ffffffc07d9fffff]
     
129. [
     
130.    0.000000] Memory: 1943148K/2064384K available (10814K kernel code,
     
131. 1580K rwdata, 4016K rodata, 1088K init, 729K bss, 121236K reserved, 0K
     
132. cma-reserved)
     
133. [    0.000000] Virtual kernel memory layout:
     
134. [    0.000000]     modules : 0xffffff8000000000 - 0xffffff8008000000   (   128 MB)
     
135. [    0.000000]     vmalloc : 0xffffff8008000000 - 0xffffffbdbfff0000   (   246 GB)
     
136. [    0.000000]       .init : 0xffffff8008f00000 - 0xffffff8009010000   (  1088 KB)
     
137. [    0.000000]       .text : 0xffffff8008080000 - 0xffffff8008b10000   ( 10816 KB)
     
138. [    0.000000]     .rodata : 0xffffff8008b10000 - 0xffffff8008f00000   (  4032 KB)
     
139. [    0.000000]       .data : 0xffffff8009010000 - 0xffffff800919b008   (  1581 KB)
     
140. [    0.000000]     vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000   (     8 GB maximum)
     
141. [    0.000000]               0xffffffbdc0008000 - 0xffffffbdc2000000   (    31 MB actual)
     
142. [    0.000000]     fixed   : 0xffffffbffe7fb000 - 0xffffffbffec00000   (  4116 KB)
     
143. [    0.000000]     PCI I/O : 0xffffffbffee00000 - 0xffffffbfffe00000   (    16 MB)
     
144. [    0.000000]     memory  : 0xffffffc000200000 - 0xffffffc080000000   (  2046 MB)
     
145. [    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1
     
146. [    0.000000] Hierarchical RCU implementation.
     
147. [    0.000000]  Build-time adjustment of leaf fanout to 64.
     
148. [    0.000000]  RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=6.
     
149. [    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=6
     
150. [    0.000000] NR_IRQS:64 nr_irqs:64 0
     
151. [    0.000000] GIC: Using split EOI/Deactivate mode
     
152. [    0.000000] ITS: /interrupt-controller@fee00000/interrupt-controller@fee20000
     
153. [    0.000000] ITS: allocated 65536 Devices @a300000 (psz 64K, shr 0)
     
154. [    0.000000] ITS: using cache flushing for cmd queue
     
155. [    0.000000] GIC: using LPI property table @0x000000000a290000
     
156. [    0.000000] ITS: Allocated 1792 chunks for LPIs
     
157. [    0.000000] CPU0: found redistributor 0 region 0:0x00000000fef00000
     
158. [    0.000000] CPU0: using LPI pending table @0x000000000a2a0000
     
159. [    0.000000] GIC: using cache flushing for LPI property table
     
160. [    0.000000] GIC: PPI partition interrupt-partition-0[0] { /cpus/cpu@0[0] /cpus/cpu@1[1] /cpus/cpu@2[2] /cpus/cpu@3[3] }
     
161. [    0.000000] GIC: PPI partition interrupt-partition-1[1] { /cpus/cpu@100[4] /cpus/cpu@101[5] }
     
162. [
     
163.    0.000000] rockchip_clk_register_frac_branch: could not find
     
164. dclk_vop0_frac as parent of dclk_vop0, rate changes may not work
     
165. [   
     
166. 0.000000] rockchip_clk_register_frac_branch: could not find
     
167. dclk_vop1_frac as parent of dclk_vop1, rate changes may not work
     
168. [    0.000000] rockchip_cpuclk_pre_rate_change: limiting alt-divider 33 to 31
     
169. [    0.000000] Architected cp15 timer(s) running at 24.00MHz (phys).
     
170. [    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
     
171. [    0.000005] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
     
172. [    0.001270] Console: colour dummy device 80x25
     
173. [    0.001294] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=24000)
     
174. [    0.001306] pid_max: default: 32768 minimum: 301
     
175. [    0.001454] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
     
176. [    0.001465] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
     
177. [    0.002147] Initializing cgroup subsys devices
     
178. [    0.002164] Initializing cgroup subsys freezer
     
179. [    0.002189] ftrace: allocating 39257 entries in 154 pages
     
180. [    0.098517] sched-energy: Sched-energy-costs installed from DT
     
181. [    0.098533] CPU0: update cpu_capacity 401
     
182. [    0.098588] ASID allocator initialised with 32768 entries
     
183. [    0.101445] PCI/MSI: /interrupt-controller@fee00000/interrupt-controller@fee20000 domain created
     
184. [    0.101929] Platform MSI: /interrupt-controller@fee00000/interrupt-controller@fee20000 domain created
     
185. [    0.103146] Detected VIPT I-cache on CPU1
     
186. [    0.103178] CPU1: found redistributor 1 region 0:0x00000000fef20000
     
187. [    0.103206] CPU1: using LPI pending table @0x0000000000310000
     
188. [    0.103247] CPU1: update cpu_capacity 401
     
189. [    0.103251] CPU1: Booted secondary processor [410fd034]
     
190. [    0.103781] Detected VIPT I-cache on CPU2
     
191. [    0.103802] CPU2: found redistributor 2 region 0:0x00000000fef40000
     
192. [    0.103829] CPU2: using LPI pending table @0x0000000000340000
     
193. [    0.103856] CPU2: update cpu_capacity 401
     
194. [    0.103859] CPU2: Booted secondary processor [410fd034]
     
195. [    0.104374] Detected VIPT I-cache on CPU3
     
196. [    0.104394] CPU3: found redistributor 3 region 0:0x00000000fef60000
     
197. [    0.104421] CPU3: using LPI pending table @0x0000000000390000
     
198. [    0.104446] CPU3: update cpu_capacity 401
     
199. [    0.104450] CPU3: Booted secondary processor [410fd034]
     
200. [    0.104957] Detected PIPT I-cache on CPU4
     
201. [    0.104984] CPU4: found redistributor 100 region 0:0x00000000fef80000
     
202. [    0.105023] CPU4: using LPI pending table @0x00000000003c0000
     
203. [    0.105062] CPU4: update cpu_capacity 1024
     
204. [    0.105066] CPU4: Booted secondary processor [410fd082]
     
205. [    0.105597] Detected PIPT I-cache on CPU5
     
206. [    0.105616] CPU5: found redistributor 101 region 0:0x00000000fefa0000
     
207. [    0.105652] CPU5: using LPI pending table @0x00000000003f0000
     
208. [    0.105680] CPU5: update cpu_capacity 1024
     
209. [    0.105683] CPU5: Booted secondary processor [410fd082]
     
210. [    0.105769] Brought up 6 CPUs
     
211. [    0.105848] SMP: Total of 6 processors activated.
     
212. [    0.105857] CPU features: detected feature: GIC system register CPU interface
     
213. [    0.105870] CPU: All CPU(s) started at EL2
     
214. [    0.105916] alternatives: patching kernel code
     
215. [    0.107281] devtmpfs: initialized
     
216. [    0.121525] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
     
217. [    0.121549] futex hash table entries: 2048 (order: 5, 131072 bytes)
     
218. [    0.122001] pinctrl core: initialized pinctrl subsystem
     
219. [    0.122731] NET: Registered protocol family 16
     
220. [    0.126841] cpuidle: using governor ladder
     
221. [    0.130861] cpuidle: using governor menu
     
222. [    0.130879] Registered FIQ tty driver
     
223. [    0.131072] vdso: 2 pages (1 code @ ffffff8008b16000, 1 data @ ffffff8009014000)
     
224. [    0.131100] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
     
225. [    0.131262] DMA: preallocated 256 KiB pool for atomic allocations
     
226. [    0.213709] console [ttyFIQ0] enabled
     
227. [    0.214243] Registered fiq debugger ttyFIQ0
     
228. [    0.243853] iommu: Adding device ff650000.vpu_service to group 0
     
229. [    0.244467] iommu: Adding device ff660000.rkvdec to group 1
     
230. [    0.245057] iommu: Adding device ff8f0000.vop to group 2
     
231. [    0.245608] iommu: Adding device ff900000.vop to group 3
     
232. [    0.247377] SCSI subsystem initialized
     
233. [    0.247895] usbcore: registered new interface driver usbfs
     
234. [    0.248417] usbcore: registered new interface driver hub
     
235. [    0.248974] usbcore: registered new device driver usb
     
236. [
     
237.    [    0.303948] thermal thermal_zone1: power_allocator: sustainable_power will be estimated
     
238. [    0.304869] NET: Registered protocol family 2
     
239. [    0.305703] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
     
240. [    0.306421] TCP bind hash table entries: 16384 (order: 7, 524288 bytes)
     
241. [    0.307379] TCP: Hash tables configured (established 16384 bind 16384)
     
242. [    0.308047] UDP hash table entries: 1024 (order: 4, 98304 bytes)
     
243. [    0.308671] UDP-Lite hash table entries: 1024 (order: 4, 98304 bytes)
     
244. [    0.309507] NET: Registered protocol family 1
     
245. [    0.310195] RPC: Registered named UNIX socket transport module.
     
246. [    0.310735] RPC: Registered udp transport module.
     
247. [    0.311151] RPC: Registered tcp transport module.
     
248. [    0.311567] RPC: Registered tcp NFSv4.1 backchannel transport module.
     
249. [    0.312678] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
     
250. [    0.313473] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available
     
251. [    0.317447] Initialise system trusted keyring
     
252. [    0.326210] NFS: Registering the id_resolver key type
     
253. [    0.326696] Key type id_resolver registered
     
254. [    0.327067] Key type id_legacy registered
     
255. [    0.327484] fuse init (API version 7.23)
     
256. [    0.328219] SGI XFS with security attributes, no debug enabled
     
257. [    0.333387] NET: Registered protocol family 38
     
258. [    0.333816] Key type asymmetric registered
     
259. [    0.334193] Asymmetric key parser 'x509' registered
     
260. [    0.334786] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
     
261. [    0.335447] io scheduler noop registered
     
262. [    0.335810] io scheduler deadline registered
     
263. [    0.336312] io scheduler cfq registered (default)
     
264. [    0.338099] rockchip-usb2phy ff770000.syscon:usb2-phy@e460: vbus_drv is not assigned
     
265. [    0.343254] rockchip-pcie f8000000.pcie: no vpcie3v3 regulator found
     
266. [    0.343847] rockchip-pcie f8000000.pcie: no vpcie1v8 regulator found
     
267. [    0.344424] rockchip-pcie f8000000.pcie: no vpcie0v9 regulator found
     
268. [    0.886654] rockchip-pcie f8000000.pcie: PCIe link training gen1 timeout!
     
269. [    0.887378] rockchip-pcie: probe of f8000000.pcie failed with error -110
     
270. [    0.889094] rk-vcodec ff650000.vpu_service: no regulator for vcodec
     
271. [    0.890017] rk-vcodec ff650000.vpu_service: probe device
     
272. [    0.890540] rk-vcodec ff650000.vpu_service: vpu mmu dec ffffffc07923a410
     
273. [    0.891390] rk-vcodec ff650000.vpu_service: allocator is drm
     
274. [    0.891972] rk-vcodec ff650000.vpu_service: checking hw id 0
     
275. [    0.893139] rk-vcodec ff650000.vpu_service: could not find power_model node
     
276. [    0.893773] rk-vcodec ff650000.vpu_service: init success
     
277. [    0.894646] rk-vcodec ff660000.rkvdec: no regulator for vcodec
     
278. [    0.895632] rk-vcodec ff660000.rkvdec: probe device
     
279. [    0.896101] rk-vcodec ff660000.rkvdec: vpu mmu dec ffffffc07923ac10
     
280. [    0.896834] rk-vcodec ff660000.rkvdec: allocator is drm
     
281. [    0.897347] rk-vcodec ff660000.rkvdec: checking hw id 6876
     
282. [    0.898190] rk-vcodec ff660000.rkvdec: could not find power_model node
     
283. [    0.898787] rk-vcodec ff660000.rkvdec: init success
     
284. [    0.900624] dma-pl330 ff6d0000.dma-controller: Loaded driver for PL330 DMAC-241330
     
285. [    0.901293] dma-pl330 ff6d0000.dma-controller:       DBUFF-32x8bytes Num_Chans-6 Num_Peri-12 Num_Events-12
     
286. [    0.903508] dma-pl330 ff6e0000.dma-controller: Loaded driver for PL330 DMAC-241330
     
287. [    0.904188] dma-pl330 ff6e0000.dma-controller:       DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16
     
288. [    0.906020] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
     
289. [    0.908085] ff180000.serial: ttyS0 at MMIO 0xff180000 (irq = 36, base_baud = 1500000) is a 16550A
     
290. [    0.909184] rockchip-pinctrl pinctrl: pin gpio4-19 already requested by fiq-debugger; cannot claim for ff1a0000.smria▒▒
     
291. 
     
292.                                                                         
     
293.                                              
     
294.    [  0(0.▒̰140],vocml▒ip-pko▒▒l`pyngu▒l▒▒py~-37s▒▒ff1y<63̗▒▒▒yy|-&w▒غ▒▒▒mr:▒`08<>/;▒̳▒▒▒▒▒▒▒sxy|?~o▒▒▒▒▒▒py▒▒▒|_?▒|x~'▒▒▒▒▒▒▒x~/▒▒▒▒▒~▒▒▒▒}??/▒▒▒▒▒?▒▒▒▒▒▒▒▒▒|~??▒▒▒▒▒▒▒▒▒▒|▒▒▒▒▒▒▒▒~~~?▒▒▒▒▒▒▒▒▒▒▒▒~▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒
     

Copy the code

THE FULL LOGS OF THE IMAGE W/O SERIAL DRIVERS (FIQ on, SERIAL_8250 off)

1. DDR Version 1.08 20170320
   
2. In
   
3. Channel 0: DDR3, 800MHz
   
4. Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
   
5. Channel 1: DDR3, 800MHz
   
6. Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
   
7. 256B stride
   
8. ch 0 ddrconfig = 0x101, ddrsize = 0x20
   
9. ch 1 ddrconfig = 0x101, ddrsize = 0x20
   
10. pmugrf_os_reg[2] = 0x32817281, stride = 0x9
    
11. OUT
    
12. Boot1: 2017-04-07, version: 1.06
    
13. CPUId = 0x0
    
14. ChipType = 0x10, 1839
    
15. SdmmcInit=2 0
    
16. BootCapSize=100000
    
17. UserCapSize=7456MB
    
18. FwPartOffset=2000 , 100000
    
19. SdmmcInit=0 0
    
20. BootCapSize=0
    
21. UserCapSize=30436MB
    
22. FwPartOffset=2000 , 0
    
23. StorageInit ok = 307676
    
24. LoadTrustBL
    
25. No find bl30.bin
    
26. RunBL31 0x10000
    
27. NOTICE:  BL31: v1.3(debug):65aa5ce
    
28. NOTICE:  BL31: Built : 10:47:37, Jun 19 2018
    
29. NOTICE:  BL31: Rockchip release version: v1.1
    
30. INFO:    GICv3 with legacy support detected. ARM GICV3 driver initialized in EL3
    
31. INFO:    Using opteed sec cpu_context!
    
32. INFO:    boot cpu mask: 0
    
33. INFO:    plat_rockchip_pmu_init(1151): pd status 3e
    
34. INFO:    BL31: Initializing runtime services
    
35. INFO:    BL31: Initializing BL32
    
36. INF
    
37. [0x0] TEE-CORE:init_primary_helper:337: Initializing
    
38. (1.1.0-170-gc4654a6 #16                                                
    
39.      Wed May 30 08:54:30 UTC 2018 aarch64)
    
40. 
    
41. INF [0x0] TEE-CORE:init_primary_helper:338: Release version: 1.2
    
42. 
    
43. INF [0x0] TEE-CORE:init_teecore:83: teecore inits done
    
44. INFO:    BL31: Preparing for EL3 exit to normal world
    
45. INFO:    Entry point address = 0x200000
    
46. INFO:    SPSR = 0x3c9
    
47. 
    
48. 
    
49. U-Boot 2017.09-01874-ga60b58c (Aug 16 2018 - 15:49:09 +0200)
    
50. 
    
51. Model: Firefly-RK3399 Board
    
52. DRAM:  2 GiB
    
53. Relocation Offset is: 7fd15000
    
54. rk8xx_read: read reg 0x17 failed, ret=-121
    
55. MMC:   dwmmc@fe320000: 1, sdhci@fe330000: 0
    
56. invalid parameter
    
57. *** Warning - bad CRC, using default environment
    
58. 
    
59. In:    serial@ff1a0000
    
60. Out:   serial@ff1a0000
    
61. Err:   serial@ff1a0000
    
62. Model: Firefly-RK3399 Board
    
63. switch to partitions #0, OK
    
64. mmc1 is current device
    
65. do_rkimg_test found IDB in SDcard
    
66. Boot from SDcard
    
67. get part misc fail -1
    
68. Net:   eth0: ethernet@fe300000
    
69. Hit any key to stop autoboot:  0
    
70. android_bootloader_boot_flow Could not find misc partition
    
71. get part misc fail -1
    
72. ANDROID: reboot reason: "(none)"
    
73. ** Invalid Android Image header **
    
74. android_bootloader_boot_flow boot part load fail
    
75. Android boot failed, error -1.
    
76. get part misc fail -1
    
77. =Booting Rockchip format image=
    
78. boot_rockchip_image kernel or boot part info error
    
79. switch to partitions #0, OK
    
80. mmc1 is current device
    
81. Scanning mmc 1:4...
    
82. Found /extlinux/extlinux.conf
    
83. Retrieving file: /extlinux/extlinux.conf
    
84. reading /extlinux/extlinux.conf
    
85. 214 bytes read in 4 ms (51.8 KiB/s)
    
86. 1:      kernel-4.4
    
87. Retrieving file: /Image
    
88. reading /Image
    
89. 17911816 bytes read in 751 ms (22.7 MiB/s)
    
90. append:
    
91. earlyprintk console=ttyFIQ0,1500000n8 rw
    
92. root=PARTUUID=B921B045-1DF0-41C3-AF44-4C6F280D3FAE rootfstype=ext4
    
93. init=/sbin/init rootwait
    
94. Retrieving file: /rk3399-firefly-linux.dtb
    
95. reading /rk3399-firefly-linux.dtb
    
96. 75364 bytes read in 7 ms (10.3 MiB/s)
    
97. ## Flattened Device Tree blob at 01f00000
    
98.    Booting using the fdt blob at 0x1f00000
    
99.    Loading Device Tree to 00000000081ea000, end 00000000081ff663 ... OK
    
100. Adding bank: start=0x00200000, size=0x08200000
     
101. Adding bank: start=0x0a200000, size=0x75e00000
     
102. 
     
103. Starting kernel ...
     
104. 
     
105. 
     
106. [    0.000000] Booting Linux on physical CPU 0x0
     
107. [    0.000000] Initializing cgroup subsys cpuset
     
108. [    0.000000] Initializing cgroup subsys cpu
     
109. [    0.000000] Initializing cgroup subsys cpuacct
     
110. [
     
111.    0.000000] Linux version 4.4.114 (marijn@marijn-VirtualBox) (gcc
     
112. version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.9) ) #38 SMP
     
113. Wed Sep 19 08:15:31 CEST 2018
     
114. [    0.000000] Boot CPU: AArch64 Processor [410fd034]
     
115. [    0.000000] Reserved memory: failed to reserve memory for node 'drm-logo@00000000': base 0x0000000000000000, size 0 MiB
     
116. [    0.000000] psci: probing for conduit method from DT.
     
117. [    0.000000] psci: PSCIv1.0 detected in firmware.
     
118. [    0.000000] psci: Using standard PSCI v0.2 function IDs
     
119. [    0.000000] psci: Trusted OS migration not required
     
120. [    0.000000] PERCPU: Embedded 21 pages/cpu @ffffffc07fef6000 s45800 r8192 d32024 u86016
     
121. [    0.000000] Detected VIPT I-cache on CPU0
     
122. [    0.000000] CPU features: enabling workaround for ARM erratum 845719
     
123. [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 507912
     
124. [
     
125.    0.000000] Kernel command line: earlyprintk console=ttyFIQ0,1500000n8
     
126. rw root=PARTUUID=B921B045-1DF0-41C3-AF44-4C6F280D3FAE rootfstype=ext4
     
127. init=/sbin/init rootwait
     
128. [    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
     
129. [    0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
     
130. [    0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
     
131. [    0.000000] software IO TLB [mem 0x79a00000-0x7da00000] (64MB) mapped at [ffffffc079a00000-ffffffc07d9fffff]
     
132. [
     
133.    0.000000] Memory: 1943176K/2064384K available (10814K kernel code,
     
134. 1556K rwdata, 4000K rodata, 1088K init, 726K bss, 121208K reserved, 0K
     
135. cma-reserved)
     
136. [    0.000000] Virtual kernel memory layout:
     
137. [    0.000000]     modules : 0xffffff8000000000 - 0xffffff8008000000   (   128 MB)
     
138. [    0.000000]     vmalloc : 0xffffff8008000000 - 0xffffffbdbfff0000   (   246 GB)
     
139. [    0.000000]       .init : 0xffffff8008f00000 - 0xffffff8009010000   (  1088 KB)
     
140. [    0.000000]       .text : 0xffffff8008080000 - 0xffffff8008b10000   ( 10816 KB)
     
141. [    0.000000]     .rodata : 0xffffff8008b10000 - 0xffffff8008f00000   (  4032 KB)
     
142. [    0.000000]       .data : 0xffffff8009010000 - 0xffffff8009195008   (  1557 KB)
     
143. [    0.000000]     vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000   (     8 GB maximum)
     
144. [    0.000000]               0xffffffbdc0008000 - 0xffffffbdc2000000   (    31 MB actual)
     
145. [    0.000000]     fixed   : 0xffffffbffe7fb000 - 0xffffffbffec00000   (  4116 KB)
     
146. [    0.000000]     PCI I/O : 0xffffffbffee00000 - 0xffffffbfffe00000   (    16 MB)
     
147. [    0.000000]     memory  : 0xffffffc000200000 - 0xffffffc080000000   (  2046 MB)
     
148. [    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1
     
149. [    0.000000] Hierarchical RCU implementation.
     
150. [    0.000000]  Build-time adjustment of leaf fanout to 64.
     
151. [    0.000000]  RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=6.
     
152. [    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=6
     
153. [    0.000000] NR_IRQS:64 nr_irqs:64 0
     
154. [    0.000000] GIC: Using split EOI/Deactivate mode
     
155. [    0.000000] ITS: /interrupt-controller@fee00000/interrupt-controller@fee20000
     
156. [    0.000000] ITS: allocated 65536 Devices @a300000 (psz 64K, shr 0)
     
157. [    0.000000] ITS: using cache flushing for cmd queue
     
158. [    0.000000] GIC: using LPI property table @0x000000000a290000
     
159. [    0.000000] ITS: Allocated 1792 chunks for LPIs
     
160. [    0.000000] CPU0: found redistributor 0 region 0:0x00000000fef00000
     
161. [    0.000000] CPU0: using LPI pending table @0x000000000a2a0000
     
162. [    0.000000] GIC: using cache flushing for LPI property table
     
163. [    0.000000] GIC: PPI partition interrupt-partition-0[0] { /cpus/cpu@0[0] /cpus/cpu@1[1] /cpus/cpu@2[2] /cpus/cpu@3[3] }
     
164. [    0.000000] GIC: PPI partition interrupt-partition-1[1] { /cpus/cpu@100[4] /cpus/cpu@101[5] }
     
165. [
     
166.    0.000000] rockchip_clk_register_frac_branch: could not find
     
167. dclk_vop0_frac as parent of dclk_vop0, rate changes may not work
     
168. [   
     
169. 0.000000] rockchip_clk_register_frac_branch: could not find
     
170. dclk_vop1_frac as parent of dclk_vop1, rate changes may not work
     
171. [    0.000000] rockchip_cpuclk_pre_rate_change: limiting alt-divider 33 to 31
     
172. [    0.000000] Architected cp15 timer(s) running at 24.00MHz (phys).
     
173. [    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
     
174. [    0.000005] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
     
175. [    0.001255] Console: colour dummy device 80x25
     
176. [    0.001273] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=24000)
     
177. [    0.001286] pid_max: default: 32768 minimum: 301
     
178. [    0.001433] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
     
179. [    0.001444] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
     
180. [    0.002128] Initializing cgroup subsys devices
     
181. [    0.002146] Initializing cgroup subsys freezer
     
182. [    0.002172] ftrace: allocating 39001 entries in 153 pages
     
183. [    0.097982] sched-energy: Sched-energy-costs installed from DT
     
184. [    0.097999] CPU0: update cpu_capacity 401
     
185. [    0.098055] ASID allocator initialised with 32768 entries
     
186. [    0.100876] PCI/MSI: /interrupt-controller@fee00000/interrupt-controller@fee20000 domain created
     
187. [    0.101332] Platform MSI: /interrupt-controller@fee00000/interrupt-controller@fee20000 domain created
     
188. [    0.102548] Detected VIPT I-cache on CPU1
     
189. [    0.102580] CPU1: found redistributor 1 region 0:0x00000000fef20000
     
190. [    0.102609] CPU1: using LPI pending table @0x0000000000310000
     
191. [    0.102650] CPU1: update cpu_capacity 401
     
192. [    0.102654] CPU1: Booted secondary processor [410fd034]
     
193. [    0.103173] Detected VIPT I-cache on CPU2
     
194. [    0.103194] CPU2: found redistributor 2 region 0:0x00000000fef40000
     
195. [    0.103222] CPU2: using LPI pending table @0x0000000000330000
     
196. [    0.103248] CPU2: update cpu_capacity 401
     
197. [    0.103252] CPU2: Booted secondary processor [410fd034]
     
198. [    0.103772] Detected VIPT I-cache on CPU3
     
199. [    0.103792] CPU3: found redistributor 3 region 0:0x00000000fef60000
     
200. [    0.103819] CPU3: using LPI pending table @0x0000000000380000
     
201. [    0.103845] CPU3: update cpu_capacity 401
     
202. [    0.103849] CPU3: Booted secondary processor [410fd034]
     
203. [    0.104352] Detected PIPT I-cache on CPU4
     
204. [    0.104379] CPU4: found redistributor 100 region 0:0x00000000fef80000
     
205. [    0.104419] CPU4: using LPI pending table @0x00000000003c0000
     
206. [    0.104458] CPU4: update cpu_capacity 1024
     
207. [    0.104462] CPU4: Booted secondary processor [410fd082]
     
208. [    0.104992] Detected PIPT I-cache on CPU5
     
209. [    0.105010] CPU5: found redistributor 101 region 0:0x00000000fefa0000
     
210. [    0.105047] CPU5: using LPI pending table @0x00000000003f0000
     
211. [    0.105073] CPU5: update cpu_capacity 1024
     
212. [    0.105076] CPU5: Booted secondary processor [410fd082]
     
213. [    0.105163] Brought up 6 CPUs
     
214. [    0.105241] SMP: Total of 6 processors activated.
     
215. [    0.105250] CPU features: detected feature: GIC system register CPU interface
     
216. [    0.105263] CPU: All CPU(s) started at EL2
     
217. [    0.105308] alternatives: patching kernel code
     
218. [    0.106676] devtmpfs: initialized
     
219. [    0.120968] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
     
220. [    0.120993] futex hash table entries: 2048 (order: 5, 131072 bytes)
     
221. [    0.121447] pinctrl core: initialized pinctrl subsystem
     
222. [    0.122186] NET: Registered protocol family 16
     
223. [    0.126628] cpuidle: using governor ladder
     
224. [    0.130638] cpuidle: using governor menu
     
225. [    0.130656] Registered FIQ tty driver
     
226. [    0.130844] vdso: 2 pages (1 code @ ffffff8008b16000, 1 data @ ffffff8009014000)
     
227. [    0.130872] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
     
228. [    0.131032] DMA: preallocated 256 KiB pool for atomic allocations
     
229. [    0.213589] console [ttyFIQ0] enabled
     
230. [    0.214122] Registered fiq debugger ttyFIQ0
     
231. [    0.243712] iommu: Adding device ff650000.vpu_service to group 0
     
232. [    0.244325] iommu: Adding device ff660000.rkvdec to group 1
     
233. [    0.244910] iommu: Adding device ff8f0000.vop to group 2
     
234. [    0.245469] iommu: Adding device ff900000.vop to group 3
     
235. [    0.247225] SCSI subsystem initialized
     
236. [    0.247740] usbcore: registered new interface driver usbfs
     
237. [    0.248262] usbcore: registered new interface driver hub
     
238. [    0.248821] usbcore: registered new device driver usb
     
239. [
     
240.    [    0.886500] rockchip-pcie f8000000.pcie: PCIe link training gen1 timeout!
     
241. [    0.887223] rockchip-pcie: probe of f8000000.pcie failed with error -110
     
242. [    0.888943] rk-vcodec ff650000.vpu_service: no regulator for vcodec
     
243. [    0.889860] rk-vcodec ff650000.vpu_service: probe device
     
244. [    0.890383] rk-vcodec ff650000.vpu_service: vpu mmu dec ffffffc07923a410
     
245. [    0.891232] rk-vcodec ff650000.vpu_service: allocator is drm
     
246. [    0.891812] rk-vcodec ff650000.vpu_service: checking hw id 0
     
247. [    0.892996] rk-vcodec ff650000.vpu_service: could not find power_model node
     
248. [    0.893630] rk-vcodec ff650000.vpu_service: init success
     
249. [    0.894506] rk-vcodec ff660000.rkvdec: no regulator for vcodec
     
250. [    0.895470] rk-vcodec ff660000.rkvdec: probe device
     
251. [    0.895945] rk-vcodec ff660000.rkvdec: vpu mmu dec ffffffc07923ac10
     
252. [    0.896692] rk-vcodec ff660000.rkvdec: allocator is drm
     
253. [    0.897207] rk-vcodec ff660000.rkvdec: checking hw id 6876
     
254. [    0.898060] rk-vcodec ff660000.rkvdec: could not find power_model node
     
255. [    0.898659] rk-vcodec ff660000.rkvdec: init success
     
256. [    0.900572] dma-pl330 ff6d0000.dma-controller: Loaded driver for PL330 DMAC-241330
     
257. [    0.901242] dma-pl330 ff6d0000.dma-controller:       DBUFF-32x8bytes Num_Chans-6 Num_Peri-12 Num_Events-12
     
258. [    0.903530] dma-pl330 ff6e0000.dma-controller: Loaded driver for PL330 DMAC-241330
     
259. [    0.904199] dma-pl330 ff6e0000.dma-controller:       DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16
     
260. [    0.906253] [drm] Initialized drm 1.1.0 20060810
     
261. [
     
262.    0.909842] rockchip-▒r}0lmws▒▒y▒▒ubsvg۝▒▒▒c
     
263. y{,dksر▒▒d-▒Р▒▒▒▒yyx8=>]<ooooo▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒|▒▒~|}~~>?????▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒
     

Copy the code

THE FULL LOGS W/O UART PORTS CONFIGURED (FIQ on, UART_PORTS 0)

1. In
   
2. Channel 0: DDR3, 800MHz
   
3. Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
   
4. Channel 1: DDR3, 800MHz
   
5. Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
   
6. 256B stride
   
7. ch 0 ddrconfig = 0x101, ddrsize = 0x20
   
8. ch 1 ddrconfig = 0x101, ddrsize = 0x20
   
9. pmugrf_os_reg[2] = 0x32817281, stride = 0x9
   
10. OUT
    
11. Boot1: 2017-04-07, version: 1.06
    
12. CPUId = 0x0
    
13. ChipType = 0x10, 1830
    
14. SdmmcInit=2 0
    
15. BootCapSize=100000
    
16. UserCapSize=7456MB
    
17. FwPartOffset=2000 , 100000
    
18. SdmmcInit=0 0
    
19. BootCapSize=0
    
20. UserCapSize=30436MB
    
21. FwPartOffset=2000 , 0
    
22. StorageInit ok = 312104
    
23. LoadTrustBL
    
24. No find bl30.bin
    
25. RunBL31 0x10000
    
26. NOTICE:  BL31: v1.3(debug):65aa5ce
    
27. NOTICE:  BL31: Built : 10:47:37, Jun 19 2018
    
28. NOTICE:  BL31: Rockchip release version: v1.1
    
29. INFO:    GICv3 with legacy support detected. ARM GICV3 driver initialized in EL3
    
30. INFO:    Using opteed sec cpu_context!
    
31. INFO:    boot cpu mask: 0
    
32. INFO:    plat_rockchip_pmu_init(1151): pd status 3e
    
33. INFO:    BL31: Initializing runtime services
    
34. INFO:    BL31: Initializing BL32
    
35. INF [0x0] TEE-CORE:init_primary_helper:337: Initializing (1.1.0-170-gc4654a6 #16 Wed May 30 08:54:30 UTC 2018 aarch64)
    
36. 
    
37. INF [0x0] TEE-CORE:init_primary_helper:338: Release version: 1.2
    
38. 
    
39. INF [0x0] TEE-CORE:init_teecore:83: teecore inits done
    
40. INFO:    BL31: Preparing for EL3 exit to normal world
    
41. INFO:    Entry point address = 0x200000
    
42. INFO:    SPSR = 0x3c9
    
43. 
    
44. 
    
45. U-Boot 2017.09-01874-ga60b58c (Aug 16 2018 - 15:49:09 +0200)
    
46. 
    
47. Model: Firefly-RK3399 Board
    
48. DRAM:  2 GiB
    
49. Relocation Offset is: 7fd15000
    
50. rk8xx_read: read reg 0x17 failed, ret=-121
    
51. MMC:   dwmmc@fe320000: 1, sdhci@fe330000: 0
    
52. invalid parameter
    
53. *** Warning - bad CRC, using default environment
    
54. 
    
55. In:    serial@ff1a0000
    
56. Out:   serial@ff1a0000
    
57. Err:   serial@ff1a0000
    
58. Model: Firefly-RK3399 Board
    
59. switch to partitions #0, OK
    
60. mmc1 is current device
    
61. do_rkimg_test found IDB in SDcard
    
62. Boot from SDcard
    
63. get part misc fail -1
    
64. Net:   eth0: ethernet@fe300000
    
65. Hit any key to stop autoboot:  0
    
66. android_bootloader_boot_flow Could not find misc partition
    
67. get part misc fail -1
    
68. ANDROID: reboot reason: "(none)"
    
69. Error: Bad gzipped data
    
70. FDT load addr 0x10f00000 size 262 KiB
    
71. Booting kernel at 0x207f800 with fdt at 32d8800...
    
72. 
    
73. 
    
74. ## Booting Android Image at 0x0207f800 ...
    
75. Kernel load addr 0x02080000 size 18783 KiB
    
76. ## Flattened Device Tree blob at 032d8800
    
77.    Booting using the fdt blob at 0x32d8800
    
78.    XIP Kernel Image ... OK
    
79.    Loading Device Tree to 00000000081ea000, end 00000000081ff933 ... OK
    
80. Adding bank: start=0x00200000, size=0x08200000
    
81. Adding bank: start=0x0a200000, size=0x75e00000
    
82. 
    
83. Starting kernel ...
    
84. 
    
85. 
    
86. [    0.000000] Booting Linux on physical CPU 0x0
    
87. [    0.000000] Initializing cgroup subsys cpuset
    
88. [    0.000000] Initializing cgroup subsys cpu
    
89. [    0.000000] Initializing cgroup subsys cpuacct
    
90. [
    
91.    0.000000] Linux version 4.4.143 (marijn@marijn-VirtualBox) (gcc
    
92. version 6.3.1 20170404 (Linaro GCC 6.3-2017.05) ) #4 SMP Fri Aug 17
    
93. 08:52:06 CEST 2018
    
94. [    0.000000] Boot CPU: AArch64 Processor [410fd034]
    
95. [    0.000000] earlycon: Early serial console at MMIO32 0xff1a0000 (options '')
    
96. [    0.000000] bootconsole [uart0] enabled
    
97. [    0.000000] Reserved memory: failed to reserve memory for node 'drm-logo@00000000': base 0x0000000000000000, size 0 MiB
    
98. [    0.000000] psci: probing for conduit method from DT.
    
99. [    0.000000] psci: PSCIv1.0 detected in firmware.
    
100. [    0.000000] psci: Using standard PSCI v0.2 function IDs
     
101. [    0.000000] psci: Trusted OS migration not required
     
102. [    0.000000] PERCPU: Embedded 21 pages/cpu @ffffffc07fef9000 s45800 r8192 d32024 u86016
     
103. [    0.000000] Detected VIPT I-cache on CPU0
     
104. [    0.000000] CPU features: enabling workaround for ARM erratum 845719
     
105. [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 507912
     
106. [
     
107.    0.000000] Kernel command line: sdfwupdate storagemedia=sd
     
108. androidboot.mode=sd androidboot.slot_suffix=
     
109. androidboot.serialno=e251fb7457dd2c0d  rw rootwait
     
110. earlycon=uart8250,mmio32,0xff1a0000 swiotlb=1 console=ttyFIQ0
     
111. root=PARTUUID=614e0000-0000 rootfstype=ext4
     
112. [    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
     
113. [    0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
     
114. [    0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
     
115. [    0.000000] software IO TLB [mem 0x7feb1000-0x7fef1000] (0MB) mapped at [ffffffc07feb1000-ffffffc07fef0fff]
     
116. [
     
117.    0.000000] Memory: 2007524K/2064384K available (11518K kernel code,
     
118. 1694K rwdata, 4400K rodata, 1088K init, 754K bss, 56860K reserved, 0K
     
119. cma-reserved)
     
120. [    0.000000] Virtual kernel memory layout:
     
121. [    0.000000]     modules : 0xffffff8000000000 - 0xffffff8008000000   (   128 MB)
     
122. [    0.000000]     vmalloc : 0xffffff8008000000 - 0xffffffbdbfff0000   (   246 GB)
     
123. [    0.000000]       .init : 0xffffff8008f80000 - 0xffffff80090a0000   (  1152 KB)
     
124. [    0.000000]       .text : 0xffffff8008080000 - 0xffffff8008b60000   ( 11136 KB)
     
125. [    0.000000]     .rodata : 0xffffff8008b60000 - 0xffffff8008f80000   (  4224 KB)
     
126. [    0.000000]       .data : 0xffffff80090a0000 - 0xffffff8009229808   (  1575 KB)
     
127. [    0.000000]     vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000   (     8 GB maximum)
     
128. [    0.000000]               0xffffffbdc0008000 - 0xffffffbdc2000000   (    31 MB actual)
     
129. [    0.000000]     fixed   : 0xffffffbffe7fb000 - 0xffffffbffec00000   (  4116 KB)
     
130. [    0.000000]     PCI I/O : 0xffffffbffee00000 - 0xffffffbfffe00000   (    16 MB)
     
131. [    0.000000]     memory  : 0xffffffc000200000 - 0xffffffc080000000   (  2046 MB)
     
132. [    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1
     
133. [    0.000000] Hierarchical RCU implementation.
     
134. [    0.000000]  Build-time adjustment of leaf fanout to 64.
     
135. [    0.000000]  RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=6.
     
136. [    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=6
     
137. [    0.000000] NR_IRQS:64 nr_irqs:64 0
     
138. [    0.000000] GIC: Using split EOI/Deactivate mode
     
139. [    0.000000] ITS: /interrupt-controller@fee00000/interrupt-controller@fee20000
     
140. [    0.000000] ITS: allocated 65536 Devices @a300000 (psz 64K, shr 0)
     
141. [    0.000000] ITS: using cache flushing for cmd queue
     
142. [    0.000000] GIC: using LPI property table @0x000000000a290000
     
143. [    0.000000] ITS: Allocated 1792 chunks for LPIs
     
144. [    0.000000] CPU0: found redistributor 0 region 0:0x00000000fef00000
     
145. [    0.000000] CPU0: using LPI pending table @0x000000000a2a0000
     
146. [    0.000000] GIC: using cache flushing for LPI property table
     
147. [    0.000000] GIC: PPI partition interrupt-partition-0[0] { /cpus/cpu@0[0] /cpus/cpu@1[1] /cpus/cpu@2[2] /cpus/cpu@3[3] }
     
148. [    0.000000] GIC: PPI partition interrupt-partition-1[1] { /cpus/cpu@100[4] /cpus/cpu@101[5] }
     
149. [
     
150.    0.000000] rockchip_clk_register_frac_branch: could not find
     
151. dclk_vop0_frac as parent of dclk_vop0, rate changes may not work
     
152. [   
     
153. 0.000000] rockchip_clk_register_frac_branch: could not find
     
154. dclk_vop1_frac as parent of dclk_vop1, rate changes may not work
     
155. [    0.000000] rockchip_cpuclk_pre_rate_change: limiting alt-divider 33 to 31
     
156. [    0.000000] Architected cp15 timer(s) running at 24.00MHz (phys).
     
157. [    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
     
158. [    0.000005] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
     
159. [    0.001257] Console: colour dummy device 80x25
     
160. [    0.001276] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=24000)
     
161. [    0.001289] pid_max: default: 32768 minimum: 301
     
162. [    0.001434] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
     
163. [    0.001445] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
     
164. [    0.002121] Initializing cgroup subsys devices
     
165. [    0.002138] Initializing cgroup subsys freezer
     
166. [    0.002163] ftrace: allocating 40726 entries in 160 pages
     
167. [    0.102127] sched-energy: Sched-energy-costs installed from DT
     
168. [    0.102143] CPU0: update cpu_capacity 401
     
169. [    0.102198] ASID allocator initialised with 32768 entries
     
170. [    0.105145] PCI/MSI: /interrupt-controller@fee00000/interrupt-controller@fee20000 domain created
     
171. [    0.105615] Platform MSI: /interrupt-controller@fee00000/interrupt-controller@fee20000 domain created
     
172. [    0.106839] Detected VIPT I-cache on CPU1
     
173. [    0.106872] CPU1: found redistributor 1 region 0:0x00000000fef20000
     
174. [    0.106901] CPU1: using LPI pending table @0x0000000000310000
     
175. [    0.106943] CPU1: update cpu_capacity 401
     
176. [    0.106947] CPU1: Booted secondary processor [410fd034]
     
177. [    0.107504] Detected VIPT I-cache on CPU2
     
178. [    0.107525] CPU2: found redistributor 2 region 0:0x00000000fef40000
     
179. [    0.107552] CPU2: using LPI pending table @0x0000000000340000
     
180. [    0.107581] CPU2: update cpu_capacity 401
     
181. [    0.107584] CPU2: Booted secondary processor [410fd034]
     
182. [    0.108082] Detected VIPT I-cache on CPU3
     
183. [    0.108102] CPU3: found redistributor 3 region 0:0x00000000fef60000
     
184. [    0.108128] CPU3: using LPI pending table @0x0000000000390000
     
185. [    0.108156] CPU3: update cpu_capacity 401
     
186. [    0.108159] CPU3: Booted secondary processor [410fd034]
     
187. [    0.108674] Detected PIPT I-cache on CPU4
     
188. [    0.108701] CPU4: found redistributor 100 region 0:0x00000000fef80000
     
189. [    0.108740] CPU4: using LPI pending table @0x00000000003c0000
     
190. [    0.108779] CPU4: update cpu_capacity 1024
     
191. [    0.108783] CPU4: Booted secondary processor [410fd082]
     
192. [    0.109329] Detected PIPT I-cache on CPU5
     
193. [    0.109347] CPU5: found redistributor 101 region 0:0x00000000fefa0000
     
194. [    0.109384] CPU5: using LPI pending table @0x00000000003f0000
     
195. [    0.109411] CPU5: update cpu_capacity 1024
     
196. [    0.109414] CPU5: Booted secondary processor [410fd082]
     
197. [    0.109500] Brought up 6 CPUs
     
198. [    0.109578] SMP: Total of 6 processors activated.
     
199. [    0.109587] CPU features: detected feature: GIC system register CPU interface
     
200. [    0.109600] CPU: All CPU(s) started at EL2
     
201. [    0.109646] alternatives: patching kernel code
     
202. [    0.111026] devtmpfs: initialized
     
203. [    0.125367] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
     
204. [    0.125391] futex hash table entries: 2048 (order: 5, 131072 bytes)
     
205. [    0.125848] pinctrl core: initialized pinctrl subsystem
     
206. [    0.126587] NET: Registered protocol family 16
     
207. [    0.131574] cpuidle: using governor ladder
     
208. [    0.135583] cpuidle: using governor menu
     
209. [    0.135599] Registered FIQ tty driver
     
210. [    0.135788] vdso: 2 pages (1 code @ ffffff8008b66000, 1 data @ ffffff80090a4000)
     
211. [    0.135815] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
     
212. [    0.135978] DMA: preallocated 256 KiB pool for atomic allocations
     
213. [    0.218372] console [ttyFIQ0] enabled
     
214. [    0.218907] Registered fiq debugger ttyFIQ0
     
215. [    0.248459] iommu: Adding device ff650000.vpu_service to group 0
     
216. [    0.249074] iommu: Adding device ff660000.rkvdec to group 1
     
217. [    0.249661] iommu: Adding device ff8f0000.vop to group 2
     
218. [    0.250214] iommu: Adding device ff900000.vop to group 3
     
219. [    0.251969] SCSI subsystem initialized
     
220. [    0.252482] usbcore: registered new interface driver usbfs
     
221. [    0.253005] usbcore: registered new interface driver hub
     
222. [    0.253565] usbcore: registered new device driver usb
     
223. [    0.308793] thermal thermal_zone1: power_allocator: sustainable_power will be estimated
     
224. [    0.309717] NET: Registered protocol family 2
     
225. [    0.310549] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
     
226. [    0.311283] TCP bind hash table entries: 16384 (order: 7, 524288 bytes)
     
227. [    0.312274] TCP: Hash tables configured (established 16384 bind 16384)
     
228. [    0.312934] UDP hash table entries: 1024 (order: 4, 98304 bytes)
     
229. [    0.313563] UDP-Lite hash table entries: 1024 (order: 4, 98304 bytes)
     
230. [    0.314401] NET: Registered protocol family 1
     
231. [    0.315074] RPC: Registered named UNIX socket transport module.
     
232. [    0.315615] RPC: Registered udp transport module.
     
233. [    0.316032] RPC: Registered tcp transport module.
     
234. [    0.316456] RPC: Registered tcp NFSv4.1 backchannel transport module.
     
235. [    0.317564] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
     
236. [    0.318386] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available
     
237. [    0.322189] Initialise system trusted keyring
     
238. [    0.330861] NFS: Registering the id_resolver key type
     
239. [    0.331347] Key type id_resolver registered
     
240. [    0.331717] Key type id_legacy registered
     
241. [    0.332130] fuse init (API version 7.23)
     
242. [    0.332862] SGI XFS with security attributes, no debug enabled
     
243. [    0.338091] NET: Registered protocol family 38
     
244. [    0.338518] Key type asymmetric registered
     
245. [    0.338893] Asymmetric key parser 'x509' registered
     
246. [    0.339486] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
     
247. [    0.340156] io scheduler noop registered
     
248. [    0.340509] io scheduler deadline registered
     
249. [    0.341014] io scheduler cfq registered (default)
     
250. [    0.342788] rockchip-usb2phy ff770000.syscon:usb2-phy@e460: vbus_drv is not assigned
     
251. [    0.347993] rockchip-pcie f8000000.pcie: no vpcie3v3 regulator found
     
252. [    0.348587] rockchip-pcie f8000000.pcie: no vpcie1v8 regulator found
     
253. [    0.349174] rockchip-pcie f8000000.pcie: no vpcie0v9 regulator found
     
254. [    0.891221] rockchip-pcie f8000000.pcie: PCIe link training gen1 timeout!
     
255. [    0.891942] rockchip-pcie: probe of f8000000.pcie failed with error -110
     
256. [    0.893659] rk-vcodec ff650000.vpu_service: no regulator for vcodec
     
257. [    0.894577] rk-vcodec ff650000.vpu_service: probe device
     
258. [    0.895099] rk-vcodec ff650000.vpu_service: vpu mmu dec ffffffc079242410
     
259. [    0.895948] rk-vcodec ff650000.vpu_service: allocator is drm
     
260. [    0.896528] rk-vcodec ff650000.vpu_service: checking hw id 0
     
261. [    0.897689] rk-vcodec ff650000.vpu_service: could not find power_model node
     
262. [    0.898323] rk-vcodec ff650000.vpu_service: init success
     
263. [    0.899196] rk-vcodec ff660000.rkvdec: no regulator for vcodec
     
264. [    0.900125] rk-vcodec ff660000.rkvdec: probe device
     
265. [    0.900625] rk-vcodec ff660000.rkvdec: vpu mmu dec ffffffc079242c10
     
266. [    0.901369] rk-vcodec ff660000.rkvdec: allocator is drm
     
267. [    0.901885] rk-vcodec ff660000.rkvdec: checking hw id 6876
     
268. [    0.902736] rk-vcodec ff660000.rkvdec: could not find power_model node
     
269. [    0.903325] rk-vcodec ff660000.rkvdec: init success
     
270. [    0.905219] dma-pl330 ff6d0000.dma-controller: Loaded driver for PL330 DMAC-241330
     
271. [    0.905889] dma-pl330 ff6d0000.dma-controller:       DBUFF-32x8bytes Num_Chans-6 Num_Peri-12 Num_Events-12
     
272. [    0.908140] dma-pl330 ff6e0000.dma-controller: Loaded driver for PL330 DMAC-241330
     
273. [    0.908821] dma-pl330 ff6e0000.dma-controller:       DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16
     
274. [    0.911054] dw-apb-uart: probe of ff180000.serial failed with error -28
     
275. [    0.911728] rockchip-pinctrl pinctrl: pin gpio4-19 already requested by fiq-debugger; cannot claim for ff1a0000.serial
     
276. [    0.912680] rockchip-pinctrl pinctrl: pin-147 (ff1a0000.serial) status -22
     
277. [    0.913296] rockchip-pinctrl pinctrl: could not request pin 147 (gpio4-19) from group uart2c-xfer  on device rockchip-pinctrl
     
278. [    0.913293] dw-apb-uart ff1a0000.serial: Error applying setting, reverse things back
     
279. [!▒▒▒p>=75▒0▒] /c▒▒-▒▒▒t:,vs▒l▒▒▒fv9m6̟8gs▒ض▒▒▒y|}n#▒▒▒▒`uzzo

Copy the code

THE FULL LOGS OF THE IMAGE WITHOUT FIQ (FIQ off)

1. DDR Version 1.08 20170320
   
2. In
   
3. Channel 0: DDR3, 800MHz
   
4. Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
   
5. Channel 1: DDR3, 800MHz
   
6. Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
   
7. 256B stride
   
8. ch 0 ddrconfig = 0x101, ddrsize = 0x20
   
9. ch 1 ddrconfig = 0x101, ddrsize = 0x20
   
10. pmugrf_os_reg[2] = 0x32817281, stride = 0x9
    
11. OUT
    
12. Boot1: 2017-04-07, version: 1.06
    
13. CPUId = 0x0
    
14. ChipType = 0x10, 1842
    
15. SdmmcInit=2 0
    
16. BootCapSize=100000
    
17. UserCapSize=7456MB
    
18. FwPartOffset=2000 , 100000
    
19. SdmmcInit=0 0
    
20. BootCapSize=0
    
21. UserCapSize=30436MB
    
22. FwPartOffset=2000 , 0
    
23. StorageInit ok = 316769
    
24. LoadTrustBL
    
25. No find bl30.bin
    
26. RunBL31 0x10000
    
27. NOTICE:  BL31: v1.3(debug):65aa5ce
    
28. NOTICE:  BL31: Built : 10:47:37, Jun 19 2018
    
29. NOTICE:  BL31: Rockchip release version: v1.1
    
30. INFO:    GICv3 with legacy support detected. ARM GICV3 driver initialized in EL3
    
31. INFO:    Using opteed sec cpu_context!
    
32. INFO:    boot cpu mask: 0
    
33. INFO:    plat_rockchip_pmu_init(1151): pd status 3e
    
34. INFO:    BL31: Initializing runtime services
    
35. INFO:    BL31: Initializing BL32
    
36. INF [0x0] TEE-CORE:init_primary_helper:337: Initializing (1.1.0-170-gc4654a6 #16 Wed May 30 08:54:30 UTC 2018 aarch64)
    
37. 
    
38. INF [0x0] TEE-CORE:init_primary_helper:338: Release version: 1.2
    
39. 
    
40. INF [0x0] TEE-CORE:init_teecore:83: teecore inits done
    
41. INFO:    BL31: Preparing for EL3 exit to normal world
    
42. INFO:    Entry point address = 0x200000
    
43. INFO:    SPSR = 0x3c9
    
44. 
    
45. 
    
46. U-Boot 2017.09-01874-ga60b58c (Aug 16 2018 - 15:49:09 +0200)
    
47. 
    
48. Model: Firefly-RK3399 Board
    
49. DRAM:  2 GiB
    
50. Relocation Offset is: 7fd15000
    
51. rk8xx_read: read reg 0x17 failed, ret=-121
    
52. MMC:   dwmmc@fe320000: 1, sdhci@fe330000: 0
    
53. invalid parameter
    
54. *** Warning - bad CRC, using default environment
    
55. 
    
56. In:    serial@ff1a0000
    
57. Out:   serial@ff1a0000
    
58. Err:   serial@ff1a0000
    
59. Model: Firefly-RK3399 Board
    
60. switch to partitions #0, OK
    
61. mmc1 is current device
    
62. do_rkimg_test found IDB in SDcard
    
63. Boot from SDcard
    
64. get part misc fail -1
    
65. Net:   eth0: ethernet@fe300000
    
66. Hit any key to stop autoboot:  0
    
67. android_bootloader_boot_flow Could not find misc partition
    
68. get part misc fail -1
    
69. ANDROID: reboot reason: "(none)"
    
70. ** Invalid Android Image header **
    
71. android_bootloader_boot_flow boot part load fail
    
72. Android boot failed, error -1.
    
73. get part misc fail -1
    
74. =Booting Rockchip format image=
    
75. boot_rockchip_image kernel or boot part info error
    
76. switch to partitions #0, OK
    
77. mmc1 is current device
    
78. Scanning mmc 1:4...
    
79. Found /extlinux/extlinux.conf
    
80. Retrieving file: /extlinux/extlinux.conf
    
81. reading /extlinux/extlinux.conf
    
82. 214 bytes read in 4 ms (51.8 KiB/s)
    
83. 1:      kernel-4.4
    
84. Retrieving file: /Image
    
85. reading /Image
    
86. 17846280 bytes read in 749 ms (22.7 MiB/s)
    
87. append: earlyprintk console=ttyFIQ0,1500000n8 rw root=PARTUUID=B921B045-1DF0-41C3-AF44-4C6F280D3FAE rootfstype=ext4 init=/sbin/init rootwait
    
88. Retrieving file: /rk3399-firefly-linux.dtb
    
89. reading /rk3399-firefly-linux.dtb
    
90. 75364 bytes read in 7 ms (10.3 MiB/s)
    
91. ## Flattened Device Tree blob at 01f00000
    
92.    Booting using the fdt blob at 0x1f00000
    
93.    Loading Device Tree to 00000000081ea000, end 00000000081ff663 ... OK
    
94. Adding bank: start=0x00200000, size=0x08200000
    
95. Adding bank: start=0x0a200000, size=0x75e00000
    
96. 
    
97. Starting kernel ...
    

Copy the code