Android SDK Build fails to boot

jas-rk

I've built an Android image as per the wiki instructions and flashed the follow to replace the exsiting emmc partitions from the directory rockdev/Image-rk3288.

misc.img

boot.img

system.img

resource.img

kernel.img

Android fails to start, boot output is below. Unfortunately the instructions are vague about what need be flashed.

1. U-Boot 2014.10-RK3288-02 (Dec 19 2014 - 19:50:49)
   
2. 
   
3. CPU: rk3288
   
4. CPU's clock information:
   
5.     arm pll = 600000000HZ
   
6.     periph pll = 300000000HZ
   
7.     ddr pll = 200000000HZ
   
8.     codec pll = 594000000HZ
   
9. Board:  Rockchip platform Board
   
10. DRAM:  Found dram banks:1
    
11. Adding bank:0000000000000000(0000000080000000)
    
12. 128 MiB
    
13. storage init OK!
    
14. Using default environment
    
15. 
    
16. GetParam
    
17. check parameter success
    
18. Unknow param: MACHINE_MODEL:rk30sdk!
    
19. Unknow param: MACHINE_ID:007!
    
20. Unknow param: MANUFACTURER:RK30SDK!
    
21. Unknow param: PWR_HLD: 0,0,A,0,1!
    
22. failed to prepare fdt from boot!
    
23. power key: bank-0 pin-5
    
24. can't find dts node for ricoh619
    
25. pmic:act8846
    
26. Can't find dts node for fuel guage cw201x
    
27. SecureBootEn = 0, SecureBootLock = 0
    
28. 
    
29. #Boot ver: 2014-12-19#2.17
    
30. sn:1006120001000110
    
31. checkKey
    
32. vbus = 1
    
33. no fuel gauge found
    
34. no fuel gauge found
    
35. read logo_on switch from dts [0]
    
36. no fuel gauge found
    
37. Hit any key to stop autoboot:  0
    
38. failed to load fdt from boot!
    
39. kernel   @ 0x02000000 (0x005f05b0)
    
40. ramdisk  @ 0x04bf0000 (0x00120f7d)
    
41. Secure Boot state: 0
    
42. bootrk: do_bootm_linux...
    
43.    Loading Device Tree to 0480c000, end 04827200 ... OK
    
44. Add bank:0000000000000000, 0000000080000000
    
45. 
    
46. Starting kernel ...[    0.000000] Booting Linux on physical CPU 0x500
    
47. [    0.000000] Initializing cgroup subsys cpu
    
48. [    0.000000] Initializing cgroup subsys cpuacct
    
49. [    0.000000] Linux version 3.10.0 (mtx512@mtx512-Inspiron-620) (gcc version 4.8.2 (Ubuntu/Linaro 4.8.2-16ubuntu4) ) #4 SMP PREEMP4
    
50. [    0.000000] CPU: ARMv7 Processor [410fc0d1] revision 1 (ARMv7), cr=10c5387d
    
51. [    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
    
52. [    0.000000] Machine: Rockchip RK3288 (Flattened Device Tree), model: rockchip,rk3288
    
53. [    0.000000] hdmi init vic is -1
    
54. [    0.000000] rockchip_ion_reserve
    
55. [    0.000000] cma: CMA: reserved 16 MiB at 2e800000
    
56. [    0.000000] Memory policy: ECC disabled, Data cache writealloc
    
57. [    0.000000] PERCPU: Embedded 9 pages/cpu @c1e86000 s13952 r8192 d14720 u36864
    
58. [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 522768
    
59. [    0.000000] Kernel command line: console=ttyFIQ0 androidboot.hardware=rk30board androidboot.console=ttyFIQ0 board.ap_has_alsa=0 0
    
60. [    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
    
61. [    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
    
62. [    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
    
63. [    0.000000] Memory: 2048MB = 2048MB total
    
64. [    0.000000] Memory: 2047276k/2047276k available, 49876k reserved, 1318912K highmem
    
65. [    0.000000] Virtual kernel memory layout:
    
66. [    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    
67. [    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    
68. [    0.000000]     vmalloc : 0xf0000000 - 0xff000000   ( 240 MB)
    
69. [    0.000000]     lowmem  : 0xc0000000 - 0xef800000   ( 760 MB)
    
70. [    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    
71. [    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
    
72. [    0.000000]       .text : 0xc0008000 - 0xc0a3b784   (10446 kB)
    
73. [    0.000000]       .init : 0xc0a3c000 - 0xc0c8c680   (2370 kB)
    
74. [    0.000000]       .data : 0xc0c8e000 - 0xc0d30f18   ( 652 kB)
    
75. [    0.000000]        .bss : 0xc0d30f18 - 0xc0e4d9cc   (1139 kB)
    
76. [    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
    
77. [    0.000000] Preemptible hierarchical RCU implementation.
    
78. [    0.000000]  RCU dyntick-idle grace-period acceleration is enabled.
    
79. [    0.000000] NR_IRQS:16 nr_irqs:16 16
    
80. [    0.000000] rk_clk_tree_init start! cru base = 0xfed00000
    
81. [    0.000000] rk_get_uboot_display_flag: uboot_logo_on = 0
    
82. [    0.000000] rkclk_init_clks: cnt_parent = 7
    
83. [    0.000000] rkclk_init_clks: cnt_rate = 32
    
84. [    0.000000] Architected local timer running at 24.00MHz (phys).
    
85. [    0.000000] Switching to timer-based delay loop
    
86. [    0.000000] sched_clock: ARM arch timer >56 bits at 24000kHz, resolution 41ns
    
87. [    0.000000] process version: 0
    
88. [    0.000000] channel:0, lkg:0
    
89. [    0.000000] target-temp:95
    
90. [    0.000000] channel:2, lkg:0
    
91. [    0.000000] target-temp:95
    
92. [    0.000000] channel:0, lkg:0
    
93. [    0.000000] target-temp:95
    
94. [    0.000000] channel:1, lkg:0
    
95. [    0.000000] target-temp:95
    
96. [    0.000000] sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps every 4294967286ms
    
97. [    0.000000] Console: colour dummy device 80x30
    
98. [    0.542594] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
    
99. [    0.542644] pid_max: default: 32768 minimum: 301
    
100. [    0.542987] Security Framework initialized
     
101. [    0.543027] SELinux:  Initializing.
     
102. [    0.543256] Mount-cache hash table entries: 512
     
103. [    0.545284] Initializing cgroup subsys debug
     
104. [    0.545329] Initializing cgroup subsys freezer
     
105. [    0.545417] CPU: Testing write buffer coherency: ok
     
106. [    0.546163] /cpus/cpu@0 missing clock-frequency property
     
107. [    0.546205] /cpus/cpu@1 missing clock-frequency property
     
108. [    0.546238] /cpus/cpu@2 missing clock-frequency property
     
109. [    0.546271] /cpus/cpu@3 missing clock-frequency property
     
110. [    0.546391] CPU0: thread -1, cpu 0, socket 5, mpidr 80000500
     
111. [    0.546501] Setting up static identity map for 0xc0765120 - 0xc0765178
     
112. [    0.550878] last_log: 0x2e100000 map to 0xf0004000 and copy to 0xf0086000, size 0x80000 early 0x154a (version 3.0)
     
113. [    0.630146] CPU1: Booted secondary processor
     
114. [    0.630234] CPU1: thread -1, cpu 1, socket 5, mpidr 80000501
     
115. [    0.649879] CPU2: Booted secondary processor
     
116. [    0.649962] CPU2: thread -1, cpu 2, socket 5, mpidr 80000502
     
117. [    0.669663] CPU3: Booted secondary processor
     
118. [    0.669744] CPU3: thread -1, cpu 3, socket 5, mpidr 80000503
     
119. [    0.670097] Brought up 4 CPUs
     
120. [    0.670197] SMP: Total of 4 processors activated (192.00 BogoMIPS).
     
121. [    0.670227] CPU: All CPU(s) started in SVC mode.
     
122. [    0.672448] devtmpfs: initialized
     
123. [    0.690429] pinctrl core: initialized pinctrl subsystem
     
124. [    0.691179] regulator-dummy: no parameters
     
125. [    0.692795] NET: Registered protocol family 16
     
126. [    0.698470] DMA: preallocated 256 KiB pool for atomic coherent allocations
     
127. [    0.699425] ion_snapshot: 0x2e1b0000 map to 0xf0107000 and copy to 0xc0e28c94 (version 0.1)
     
128. [    0.699916] Registered FIQ tty driver
     
129. [    0.703401] console [ttyFIQ0] enabled
     
130. [    0.703949] Registered fiq debugger ttyFIQ0
     
131. [    0.706299] rockchip_get_bank_data:name=base start=0xff750000,end=0xff7500ff
     
132. [    0.706387] rockchip_get_bank_data:name=mux_bank0 start=0xff730084,end=0xff73008f
     
133. [    0.706476] rockchip_get_bank_data:name=pull_bank0 start=0xff730064,end=0xff73006f
     
134. [    0.706549] rockchip_get_bank_data:name=drv_bank0 start=0xff730070,end=0xff73007b
     
135. [    0.706821] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio1@ff780000 start=0xff780000,end=0xff7800ff
     
136. [    0.707059] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio2@ff790000 start=0xff790000,end=0xff7900ff
     
137. [    0.707291] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio3@ff7a0000 start=0xff7a0000,end=0xff7a00ff
     
138. [    0.707520] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio4@ff7b0000 start=0xff7b0000,end=0xff7b00ff
     
139. [    0.707748] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio5@ff7c0000 start=0xff7c0000,end=0xff7c00ff
     
140. [    0.707977] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio6@ff7d0000 start=0xff7d0000,end=0xff7d00ff
     
141. [    0.708204] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio7@ff7e0000 start=0xff7e0000,end=0xff7e00ff
     
142. [    0.708506] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio8@ff7f0000 start=0xff7f0000,end=0xff7f00ff
     
143. [    0.708762] rockchip_get_bank_data:name=/pinctrl@ff770000/gpio15@ff7f2000 start=0xff7f2000,end=0xff7f20ff
     
144. [    0.709002] rockchip_pinctrl_probe:name=RK3288-GPIO,type=3
     
145. [    0.709061] rockchip_pinctrl_probe:name=base start=0xff770000,end=0xff77013f
     
146. [    0.709114] rockchip_pinctrl_probe:name=pull start=0xff770140,end=0xff7701bf
     
147. [    0.709167] rockchip_pinctrl_probe:name=drv start=0xff7701c0,end=0xff77023f
     
148. [    0.710909] rockchip_interrupts_register:bank_num=7
     
149. [    0.717596] of_get_gpio_init_config:gpio[0] = 256, value = 0
     
150. [    0.717683] of_get_gpio_init_config:gpio[1] = 233, value = 0
     
151. [    0.717768] of_get_gpio_init_config:gpio[2] = 136, value = 0
     
152. [    0.717978] rockchip_pinctrl_probe:init ok
     
153. [    0.738644] rk_iommu ff900800.iep_mmu: (iep) Enter
     
154. [    0.739003] IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
     
155. [    0.739062] rk_iommu ff900800.iep_mmu: (iep) Initialized
     
156. [    0.739652] rk_iommu ff950800.vip_mmu: (vip) Enter
     
157. [    0.739980] IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
     
158. [    0.740034] rk_iommu ff950800.vip_mmu: (vip) Initialized
     
159. [    0.740584] rk_iommu ff930300.vopb_mmu: (vopb) Enter
     
160. [    0.740910] IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
     
161. [    0.740964] rk_iommu ff930300.vopb_mmu: (vopb) Initialized
     
162. [    0.741531] rk_iommu ff940300.vopl_mmu: (vopl) Enter
     
163. [    0.741857] IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
     
164. [    0.741911] rk_iommu ff940300.vopl_mmu: (vopl) Initialized
     
165. [    0.742494] rk_iommu ff9c0440.hevc_mmu: (hevc) Enter
     
166. [    0.742882] IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
     
167. [    0.742937] rk_iommu ff9c0440.hevc_mmu: (hevc) Initialized
     
168. [    0.743513] rk_iommu ff9a0800.vpu_mmu: (vpu) Enter
     
169. [    0.743836] IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
     
170. [    0.743890] rk_iommu ff9a0800.vpu_mmu: (vpu) Initialized
     
171. [    0.744507] rk_iommu ff914000.isp_mmu: (isp_mmu) Enter
     
172. [    0.744887] IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000.
     
173. [    0.744941] rk_iommu ff914000.isp_mmu: (isp_mmu) Initialized
     
174. [    0.750711] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
     
175. [    0.750765] hw-breakpoint: maximum watchpoint size is 4 bytes.
     
176. [    0.751403] DDR DEBUG: version 1.00 20140603
     
177. [    0.751487] DDR DEBUG: Channel a:
     
178. [    0.751524] DDR DEBUG: DDR3 Device
     
179. [    0.751572] DDR DEBUG: Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Total Capability=1024MB
     
180. [    0.751614] DDR DEBUG: Channel b:
     
181. [    0.751646] DDR DEBUG: DDR3 Device
     
182. [    0.751693] DDR DEBUG: Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Total Capability=1024MB
     
183. [    0.751736] DDR DEBUG: addr=0xd36000
     
184. [    0.751776] DDR DEBUG: stride=9, size=256, halfcap=40000000
     
185. [    0.751817] DDR DEBUG: socAddr[0]=0xd36000, socAddr[1]=0xd36100
     
186. [    0.751859] DDR DEBUG: chAddr[0]=0xd36000, chAddr[1]=0xd36000
     
187. [    0.751904] DDR DEBUG: dtar[0]=0x601a6000, dtar[1]=0x601a6000
     
188. [    0.752063] DDR DEBUG: init success!!! freq=200MHz
     
189. [    0.752100] DDR DEBUG: Channel a:
     
190. [    0.752149] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=180,90
     
191. [    0.752208] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=180,90
     
192. [    0.752268] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=180,90
     
193. [    0.752326] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=180,90
     
194. [    0.752380] DDR DEBUG: ZERR=0, ZDONE=0, ZPD=0x0, ZPU=0x0, OPD=0x0, OPU=0x0
     
195. [    0.752424] DDR DEBUG: DRV Pull-Up=0x19, DRV Pull-Dwn=0x19
     
196. [    0.752463] DDR DEBUG: ODT Pull-Up=0x2, ODT Pull-Dwn=0x2
     
197. [    0.752499] DDR DEBUG: Channel b:
     
198. [    0.752546] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=180,90
     
199. [    0.752606] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=180,90
     
200. [    0.752664] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=180,90
     
201. [    0.752722] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=4,0, DGSL=1,1 extra clock, DGPS=180,90
     
202. [    0.752776] DDR DEBUG: ZERR=0, ZDONE=0, ZPD=0x0, ZPU=0x0, OPD=0x0, OPU=0x0
     
203. [    0.752818] DDR DEBUG: DRV Pull-Up=0x19, DRV Pull-Dwn=0x19
     
204. [    0.752857] DDR DEBUG: ODT Pull-Up=0x2, ODT Pull-Dwn=0x2
     
205. [    0.829554] bio: create slabat 0
     
206. [    0.831405] Enter firefly_noatx8_init
     
207. [    0.831894] firefly_noatx8_probe 51
     
208. [    0.832614] SCSI subsystem initialized
     
209. [    0.833104] usbcore: registered new interface driver usbfs
     
210. [    0.833255] usbcore: registered new interface driver hub
     
211. [    0.833532] usbcore: registered new device driver usb
     
212. [    0.836598] rockchip_i2c ff650000.i2c: i2c-0: Rockchip I2C adapter
     
213. [    0.840937] rockchip_i2c ff140000.i2c: i2c-1: Rockchip I2C adapter
     
214. [    0.842403] rockchip_i2c ff660000.i2c: i2c-2: Rockchip I2C adapter
     
215. [    0.843851] rockchip_i2c ff150000.i2c: i2c-3: Rockchip I2C adapter
     
216. [    0.844681] rockchip_i2c ff160000.i2c: i2c-4: Rockchip I2C adapter
     
217. [    0.847570] media: Linux media interface: v0.10
     
218. [    0.847712] Linux video capture interface: v2.00
     
219. [    0.847870] pps_core: LinuxPPS API ver. 1 registered
     
220. [    0.847914] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
     
221. [    0.847997] PTP clock support registered
     
222. [    0.848442] rockchip_temp_probe,line=362
     
223. [    0.849225] tsadc ff280000.tsadc: initialized
     
224. [    0.850442] rockchip_ion_parse_dt: num_heaps = 1
     
225. [    0.850503] 0:  0  3  vmalloc  0x  (null)
     
226. [    0.851288] Rockchip ion module is successfully loaded (v1.0)
     
227. [    0.851817] Advanced Linux Sound Architecture Driver Initialized.
     
228. [    0.853034] Bluetooth: Core ver 2.16
     
229. [    0.853161] NET: Registered protocol family 31
     
230. [    0.853203] Bluetooth: HCI device and connection manager initialized
     
231. [    0.853264] Bluetooth: HCI socket layer initialized
     
232. [    0.853315] Bluetooth: L2CAP socket layer initialized
     
233. [    0.853408] Bluetooth: SCO socket layer initialized
     
234. [    0.854059] cfg80211: Calling CRDA to update world regulatory domain
     
235. [    0.856302] act8846_i2c_probe,line=898
     
236. [    0.857695] act8846_parse_dt,line=746
     
237. [    0.859217] act8846_i2c_probe: act8846_pmic_hold=1
     
238. [    0.859290] act8846_i2c_probe: act8846_pmic_sleep=1
     
239. [    0.859349] act8846_i2c_probe: act8846_pmic_cpu_det_gpio=1
     
240. [    0.859407] act8846_i2c_probe: act8846_pmic_usb_hub_reset_gpio=1
     
241. [    0.861867] act_dcdc1: 1200 mV
     
242. [    0.865546] vccio: 3300 mV
     
243. [    0.868194] vdd_logic: 7001500 mV at 1100 mV
     
244. [    0.871886] act_dcdc4: 2000 mV
     
245. [    0.873702] vccio_sd: 18003300 mV at 3300 mV
     
246. [    0.876612] act_ldo2: 1050 mV
     
247. [    0.879470] act_ldo3: 1800 mV
     
248. [    0.882325] act_ldo4: 3300 mV
     
249. [    0.885164] act_ldo5: 3300 mV
     
250. [    0.888000] act_ldo6: 1100 mV
     
251. [    0.890872] vcc_18: 1800 mV
     
252. [    0.893771] act_ldo8: 1850 mV
     
253. [    0.900298] vdd_arm: 7121500 mV at 1000 mV
     
254. [    0.906662] vdd_gpu: 7121500 mV at 1000 mV
     
255. [    0.907615] rk808_i2c_probe,line=1368
     
256. [    0.909257] The device is not rk808 -11
     
257. [    0.909516] rk808: probe of 0-001b failed with error -11
     
258. [    0.914423] Switching to clocksource arch_sys_counter
     
259. [    0.934962] usb_battery_charger_detect_synop , battery_charger_detect 1, pass DCD, dcd_state = 1
     
260. [    0.980284] rk-fb rockchip-fb: rk fb ion client create success!
     
261. [    0.980353] rk-fb rockchip-fb: rockchip framebuffer driver probe
     
262. [    0.981431] rk-screen rk_screen.9: rockchip screen probe success
     
263. [    0.982219] rk32-lvds rk32-lvds: rk32 lvds driver probe success
     
264. [    0.982952] rk32-edp ff970000.edp: screen is not edp!
     
265. [    0.983022] rk32-edp: probe of ff970000.edp failed with error -22
     
266. [    0.984273] rk3288-lcdc lcdc0: can't find power_ctr node for lcdc0
     
267. [    0.985028] graphics fb0: rockchip framebuffer registerd:fb0
     
268. [    0.986050] graphics fb1: rockchip framebuffer registerd:fb1
     
269. [    0.986582] graphics fb2: rockchip framebuffer registerd:fb2
     
270. [    0.987134] graphics fb3: rockchip framebuffer registerd:fb3
     
271. [    0.987676] graphics fb4: rockchip framebuffer registerd:fb4
     
272. [    0.989427] rk_iommu ff930300.vopb_mmu: (vopb) Enabled
     
273. [    0.989853] rk3288-lcdc lcdc0: lcdc0: dclk:148500000>>fps:60
     
274. [    0.989925] rk3288-lcdc lcdc0: wakeup from standby!
     
275. [    1.111728] alloc_buffer:ion_phy_addr=0x10000000
     
276. [    1.155043] fb0:phy:10000000>>vir:f0191000>>len:0x1800000
     
277. [    1.297568] rk3288-lcdc lcdc0: lcdc0 probe ok, iommu enabled
     
278. [    1.298803] rockchip_set_mux:warning ignore bank num 15
     
279. [    1.299248] rockchip_set_mux:warning ignore bank num 15
     
280. [    1.299642] rockchip_set_mux:warning ignore bank num 15
     
281. [    1.300029] rockchip_set_mux:warning ignore bank num 15
     
282. [    1.300425] rockchip_set_mux:warning ignore bank num 15
     
283. [    1.300817] rockchip_set_mux:warning ignore bank num 15
     
284. [    1.301708] rockchip_set_mux:warning ignore bank num 15
     
285. [    1.302248] rockchip_set_mux:warning ignore bank num 15
     
286. [    1.303078] rockchip_set_mux:warning ignore bank num 15
     
287. [    1.303573] rockchip_set_mux:warning ignore bank num 15
     
288. [    1.304397] rockchip_set_mux:warning ignore bank num 15
     
289. [    1.304887] rockchip_set_mux:warning ignore bank num 15
     
290. [    1.305724] rockchip_set_mux:warning ignore bank num 15
     
291. [    1.306223] rockchip_set_mux:warning ignore bank num 15
     
292. [    1.329074] NET: Registered protocol family 2
     
293. [    1.330487] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
     
294. [    1.330977] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
     
295. [    1.331473] TCP: Hash tables configured (established 8192 bind 8192)
     
296. [    1.331628] TCP: reno registered
     
297. [    1.331681] UDP hash table entries: 512 (order: 2, 16384 bytes)
     
298. [    1.331810] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
     
299. [    1.332450] NET: Registered protocol family 1
     
300. [    1.333048] Unpacking initramfs...
     
301. [    1.559100] Freeing initrd memory: 1152K (c4bf0000 - c4d10000)
     
302. [    1.561393] hw perfevents: enabled with ARMv7 Cortex-A12 PMU driver, 7 counters available
     
303. [    1.562923] probe device ff9a0000.vpu_service
     
304. [    1.563389] vpu_service: power on
     
305. [    1.564542] checking hw id 4831
     
306. [    1.565528] vpu_service set to auto frequency mode
     
307. [    1.565693] vcodec vpu_service: vcodec ion client create success!
     
308. [    1.566847] rk_iommu ff9a0800.vpu_mmu: (vpu) Enabled
     
309. [    1.566952] rk_iommu ff9a0800.vpu_mmu: (vpu) Disabled
     
310. [    1.567006] rk_iommu ff9a0800.vpu_mmu: rockchip_iommu_detach_device: Detached IOMMU with pgtable 0x2e277000
     
311. [    1.567053] vpu_service: power off...
     
312. [    1.567137] done
     
313. [    1.567170] init success
     
314. [    1.567328] probe device ff9c0000.hevc_service
     
315. [    1.567962] hevc_service: power on
     
316. [    1.569084] checking hw id 6867
     
317. [    1.569892] vcodec hevc_service: vcodec ion client create success!
     
318. [    1.570836] rk_iommu ff9c0440.hevc_mmu: (hevc) Enabled
     
319. [    1.570942] rk_iommu ff9c0440.hevc_mmu: (hevc) Disabled
     
320. [    1.570995] rk_iommu ff9c0440.hevc_mmu: rockchip_iommu_detach_device: Detached IOMMU with pgtable 0x2e274000
     
321. [    1.571043] hevc_service: power off...
     
322. [    1.571130] done
     
323. [    1.571163] init success
     
324. [    1.571517] rknandbase v1.0 2014-03-31
     
325. [    1.572164] rknand_probe clk rate = 148500000
     
326. [    1.572542] rknand_driver:ret = 0
     
327. [    1.573619] audit: initializing netlink socket (disabled)
     
328. [    1.573731] type=2000 audit(1.030:1): initialized
     
329. [    1.575977] bounce pool size: 64 pages
     
330. [    1.591466] fuse init (API version 7.22)
     
331. [    1.592685] msgmni has been set to 1456
     
332. [    1.598572] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
     
333. [    1.598637] io scheduler noop registered
     
334. [    1.598678] io scheduler deadline registered
     
335. [    1.599023] io scheduler cfq registered (default)
     
336. [    1.600486] Console: switching to colour frame buffer device 240x67
     
337. [    1.655372] rga ff920000.rga: rga ion client create success!
     
338. [    1.655806] rga: Driver loaded succesfully
     
339. [    1.657276] IEP Power ON
     
340. [    1.657391] iep ion client create success!
     
341. [    1.658416] rk_iommu ff900800.iep_mmu: (iep) Enabled
     
342. [    1.658507] IEP Power OFF
     
343. [    1.658552] rk_iommu ff900800.iep_mmu: (iep) Disabled
     
344. [    1.658604] rk_iommu ff900800.iep_mmu: rockchip_iommu_detach_device: Detached IOMMU with pgtable 0x2e26a000
     
345. [    1.658667] IEP Driver loaded succesfully
     
346. [    1.658965] Module initialized.
     
347. [    1.661407] dma-pl330 ffb20000.pdma: Loaded driver for PL330 DMAC-2364208
     
348. [    1.661480] dma-pl330 ffb20000.pdma:         DBUFF-64x8bytes Num_Chans-5 Num_Peri-6 Num_Events-10
     
349. [    1.665745] dma-pl330 ff250000.pdma: Loaded driver for PL330 DMAC-2364208
     
350. [    1.665816] dma-pl330 ff250000.pdma:         DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16
     
351. [    1.666572] pwm-voltage-regulator pwm_regulator.23: unable to request PWM, trying legacy API
     
352. [    1.666637] pwm-voltage-regulator pwm_regulator.23: unable to request legacy PWM
     
353. [    1.666679] pwm_regulator_probe:error
     
354. [    1.666751] platform pwm_regulator.23: Driver pwm-voltage-regulator requests probe deferral
     
355. [    1.667818] rk_serial.c v1.8 2014-03-04
     
356. [    1.668464] ff180000.serial: ttyS0 at MMIO 0xff180000 (irq = 87) is a rk29_serial.0
     
357. [    1.669060] serial ff180000.serial: membase 0xf0172000
     
358. [    1.678615] loop: module loaded
     
359. [    1.680478] SCSI Media Changer driver v0.25
     
360. [    1.681562] tun: Universal TUN/TAP device driver, 1.6
     
361. [    1.681610] tun: (C) 1999-2004 Max Krasnyansky
     
362. [    1.683334] stmmac_probe_config_dt: Can not read property: pmu_regulator.
     
363. [    1.683393] stmmac_probe_config_dt: Can not read property: pmu_enable_level.
     
364. [    1.683442] stmmac_probe_config_dt: clock input or output? (input).
     
365. [    1.683488] stmmac_probe_config_dt: TX delay(0x30).
     
366. [    1.683529] stmmac_probe_config_dt: RX delay(0x10).
     
367. [    1.683653] stmmac_probe_config_dt: is rockchip,rk3288-gmac
     
368. [    1.683694] stmmc_pltfr_init:
     
369. [    1.683730] stmmc_pltfr_init: ERROR: Get power-gpio failed.
     
370. [    1.683805] stmmc_pltfr_init: ERROR: Request gmac phy reset pin failed.
     
371. [    1.683845] stmmc_pltfr_init: init for RGMII
     
372. [    1.683885] tx delay=0x30
     
373. [    1.683885] rx delay=0x10
     
374. [    1.685414] stmmac - user ID: 0x10, Synopsys ID: 0x35
     
375. [    1.685456]  Normal descriptors
     
376. [    1.685487]  Ring mode enabled
     
377. [    1.685520]  DMA HW capability register supported
     
378. [    1.685558]  RX Checksum Offload Engine supported (type 2)
     
379. [    1.685596]  TX Checksum insertion supported
     
380. [    1.685630]  Wake-Up On Lan supported
     
381. [    1.685761]  Enable RX Mitigation via HW Watchdog Timer
     
382. [    1.687104] PPP generic driver version 2.4.2
     
383. [    1.687585] PPP BSD Compression module registered
     
384. [    1.687631] PPP Deflate Compression module registered
     
385. [    1.687696] PPP MPPE Compression module registered
     
386. [    1.687738] NET: Registered protocol family 24
     
387. [    1.687833] SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256) (6 bit encapsulation enabled).
     
388. [    1.687882] CSLIP: code copyright 1989 Regents of the University of California.
     
389. [    1.687927] Rockchip WiFi SYS interface (V1.00) ...
     
390. [    1.688165] usbcore: registered new interface driver catc
     
391. [    1.688294] usbcore: registered new interface driver kaweth
     
392. [    1.688340] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver
     
393. [    1.688468] usbcore: registered new interface driver pegasus
     
394. [    1.688605] usbcore: registered new interface driver rtl8150
     
395. [    1.688733] usbcore: registered new interface driver r8152
     
396. [    1.688775] hso: drivers/net/usb/hso.c: Option Wireless
     
397. [    1.688972] usbcore: registered new interface driver hso
     
398. [    1.689119] usbcore: registered new interface driver asix
     
399. [    1.689243] usbcore: registered new interface driver ax88179_178a
     
400. [    1.689368] usbcore: registered new interface driver cdc_ether
     
401. [    1.689530] usbcore: registered new interface driver cdc_eem
     
402. [    1.689658] usbcore: registered new interface driver dm9601
     
403. [    1.689781] usbcore: registered new interface driver dm9620
     
404. [    1.689937] usbcore: registered new interface driver smsc75xx
     
405. [    1.690091] usbcore: registered new interface driver smsc95xx
     
406. [    1.690217] usbcore: registered new interface driver gl620a
     
407. [    1.690352] usbcore: registered new interface driver net1080
     
408. [    1.690483] usbcore: registered new interface driver plusb
     
409. [    1.690614] usbcore: registered new interface driver rndis_host
     
410. [    1.690740] usbcore: registered new interface driver cdc_subset
     
411. [    1.690860] usbcore: registered new interface driver zaurus
     
412. [    1.690993] usbcore: registered new interface driver MOSCHIP usb-ethernet driver
     
413. [    1.691170] usbcore: registered new interface driver int51x1
     
414. [    1.691299] usbcore: registered new interface driver kalmia
     
415. [    1.691450] usbcore: registered new interface driver ipheth
     
416. [    1.691595] usbcore: registered new interface driver sierra_net
     
417. [    1.691727] usbcore: registered new interface driver cx82310_eth
     
418. [    1.691886] usbcore: registered new interface driver cdc_ncm
     
419. [    1.692087] usbcore: registered new interface driver qmi_wwan
     
420. [    1.692221] usbcore: registered new interface driver cdc_mbim
     
421. [    1.692265] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
     
422. [    1.695554] ehci_rk_probe f1a00000 f1a00010
     
423. [    1.695613] rockchip_ehci_host ff500000.usb: Rockchip On-Chip EHCI Host Controller
     
424. [    1.695710] rockchip_ehci_host ff500000.usb: new USB bus registered, assigned bus number 1
     
425. [    1.696712] rockchip_ehci_host ff500000.usb: irq 56, io mem 0xff500000
     
426. [    1.711695] rockchip_ehci_host ff500000.usb: USB 0.0 started, EHCI 1.00
     
427. [    1.711929] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
     
428. [    1.711993] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
     
429. [    1.712048] usb usb1: Product: Rockchip On-Chip EHCI Host Controller
     
430. [    1.712100] usb usb1: Manufacturer: Linux 3.10.0 ehci_hcd
     
431. [    1.712147] usb usb1: SerialNumber: ff500000.usb
     
432. [    1.713526] hub 1-0:1.0: USB hub found
     
433. [    1.713608] hub 1-0:1.0: 1 port detected
     
434. [    1.741183] ehci_rk_probe ok
     
435. [    1.741629] usbcore: registered new interface driver cdc_acm
     
436. [    1.741675] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
     
437. [    1.741878] usbcore: registered new interface driver usblp
     
438. [    1.742027] usbcore: registered new interface driver cdc_wdm
     
439. [    1.742239] usbcore: registered new interface driver usb-storage
     
440. [    1.742371] usbcore: registered new interface driver ums-alauda
     
441. [    1.742513] usbcore: registered new interface driver ums-cypress
     
442. [    1.742645] usbcore: registered new interface driver ums-datafab
     
443. [    1.742772] usbcore: registered new interface driver ums_eneub6250
     
444. [    1.742912] usbcore: registered new interface driver ums-freecom
     
445. [    1.743042] usbcore: registered new interface driver ums-isd200
     
446. [    1.743169] usbcore: registered new interface driver ums-jumpshot
     
447. [    1.743295] usbcore: registered new interface driver ums-karma
     
448. [    1.743422] usbcore: registered new interface driver ums-onetouch
     
449. [    1.743548] usbcore: registered new interface driver ums-sddr09
     
450. [    1.743673] usbcore: registered new interface driver ums-sddr55
     
451. [    1.743799] usbcore: registered new interface driver ums-usbat
     
452. [    1.744086] usbcore: registered new interface driver usbserial
     
453. [    1.744225] usbcore: registered new interface driver usbserial_generic
     
454. [    1.744335] usbserial: USB Serial support registered for generic
     
455. [    1.744472] usbcore: registered new interface driver option
     
456. [    1.744579] usbserial: USB Serial support registered for GSM modem (1-port)
     
457. [    1.744834] usbcore: registered new interface driver trancevibrator
     
458. [    1.744879] usb20_otg: version 3.10a 21-DEC-2012
     
459. [    1.745935] f1a80040
     
460. [    1.745984] Core Release: 3.10a
     
461. [    1.746023] Setting default values for core params
     
462. [    1.746435] Using Buffer DMA mode
     
463. [    1.746477] Periodic Transfer Interrupt Enhancement - disabled
     
464. [    1.746518] Multiprocessor Interrupt Enhancement - disabled
     
465. [    1.746560] OTG VER PARAM: 0, OTG VER FLAG: 0
     
466. [    1.746597] ^^^^^^^^^^^^^^^^^Device Mode
     
467. [    1.746641] Dedicated Tx FIFOs mode
     
468. [    1.746698] pcd_init otg_dev = ed9b2b40
     
469. [    1.747194] usb20_otg ff580000.usb: DWC OTG Controller
     
470. [    1.747291] usb20_otg ff580000.usb: new USB bus registered, assigned bus number 2
     
471. [    1.747399] usb20_otg ff580000.usb: irq 55, io mem 0x00000000
     
472. [    1.747584] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
     
473. [    1.747644] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
     
474. [    1.747698] usb usb2: Product: DWC OTG Controller
     
475. [    1.747745] usb usb2: Manufacturer: Linux 3.10.0 dwc_otg_hcd
     
476. [    1.747793] usb usb2: SerialNumber: ff580000.usb
     
477. [    1.749115] hub 2-0:1.0: USB hub found
     
478. [    1.749195] hub 2-0:1.0: 1 port detected
     
479. [    1.750116] usb20_host: version 3.10a 21-DEC-2012
     
480. [    1.753673] f1b00040
     
481. [    1.753722] Core Release: 3.10a
     
482. [    1.753761] Setting default values for core params
     
483. [    1.754206] Using Buffer DMA mode
     
484. [    1.754248] Periodic Transfer Interrupt Enhancement - disabled
     
485. [    1.754286] Multiprocessor Interrupt Enhancement - disabled
     
486. [    1.754327] OTG VER PARAM: 0, OTG VER FLAG: 0
     
487. [    1.754363] ^^^^^^^^^^^^^^^^^^Host Mode
     
488. [    1.754446] usb20_host ff540000.usb: DWC OTG Controller
     
489. [    1.754536] usb20_host ff540000.usb: new USB bus registered, assigned bus number 3
     
490. [    1.754639] usb20_host ff540000.usb: irq 57, io mem 0x00000000
     
491. [    1.754801] Init: Power Port (0)
     
492. [    1.754984] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
     
493. [    1.755045] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
     
494. [    1.755099] usb usb3: Product: DWC OTG Controller
     
495. [    1.755147] usb usb3: Manufacturer: Linux 3.10.0 dwc_otg_hcd
     
496. [    1.755195] usb usb3: SerialNumber: ff540000.usb
     
497. [    1.756547] hub 3-0:1.0: USB hub found
     
498. [    1.756624] hub 3-0:1.0: 1 port detected
     
499. [    1.758270] .. rk pwm remotectl v1.0 init
     
500. [    1.758536] remotectl probe j=0x0
     
501. [    1.759035] input: ff680000.pwm as /devices/ff680000.pwm/input/input0
     
502. [    1.759667] pwm enable val=0x646205
     
503. [    1.760549] usbcore: registered new interface driver xpad
     
504. [    1.760720] usbcore: registered new interface driver usb_acecad
     
505. [    1.760955] usbcore: registered new interface driver aiptek
     
506. [    1.761131] usbcore: registered new interface driver gtco
     
507. [    1.761293] usbcore: registered new interface driver hanwang
     
508. [    1.761447] usbcore: registered new interface driver kbtab
     
509. [    1.761625] usbcore: registered new interface driver wacom
     
510. [    1.762739] sensor_register_slave:mma8452,id=17
     
511. [    1.762788] sensor_register_slave:cm3217,id=44
     
512. [    1.762828] sensor_register_slave:cm3218,id=45
     
513. [    1.769220] rtc_hym8563 0-0051: rtc core: registered hym8563 as rtc0
     
514. [    1.769382] i2c /dev entries driver
     
515. [    1.771614] IR NEC protocol handler initialized
     
516. [    1.771664] IR RC5(x) protocol handler initialized
     
517. [    1.771702] IR RC6 protocol handler initialized
     
518. [    1.771738] IR JVC protocol handler initialized
     
519. [    1.771774] IR Sony protocol handler initialized
     
520. [    1.771809] IR RC5 (streamzap) protocol handler initialized
     
521. [    1.771847] IR SANYO protocol handler initialized
     
522. [    1.771884] IR MCE Keyboard/mouse protocol handler initialized
     
523. [    1.772133] usbcore: registered new interface driver uvcvideo
     
524. [    1.772175] USB Video Class driver (1.1.1)
     
525. [    1.772222] CamSys driver version: v0.19.0,  CamSys head file version: v0.8.0
     
526. [    1.775380] D1:camsys_platform_probe(1061): 1-gpios-cifpower: gpio=236
     
527. [    1.775469] D1:camsys_platform_probe(1064): gpios-cifpower: gpio_request
     
528. [    1.775533] D1:camsys_platform_probe(1066): 1-gpios-cifpower: gpio_request=0
     
529. [    1.775598] D1:camsys_platform_probe(1075): gpios-cifpower: 236 high
     
530. [    1.775823] D1:camsys_mipiphy_probe_cb(163): ff910000.isp mipi phy0 probe success(reg_phy: 0x0  reg_vir: 0x0  size: 0x0)
     
531. [    1.776327] D1:camsys_mipiphy_probe_cb(160): ff910000.isp mipi phy1 probe success(reg_phy: 0xff968000  reg_vir: 0xf19b0000  size)
     
532. [    1.778569] D1:camsys_platform_probe(1208): ff910000.isp memory:
     
533. [    1.778632] D1:camsys_platform_probe(1218):     Register memory (phy: 0xff910000 vir: 0xf19e0000 size: 0x10000)
     
534. [    1.778691] D1:camsys_platform_probe(1213):     I2c memory (phy: 0x2da43000 vir: 0xeda43000 size: 0x1000)
     
535. [    1.778744] D1:camsys_platform_probe(1233): Probe ff910000.isp device success
     
536. [    1.781685] device-mapper: uevent: version 1.0.3
     
537. [    1.782420] device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com
     
538. [    1.783342] Bluetooth: HCI UART driver ver 2.2
     
539. [    1.783396] Bluetooth: HCI H4 protocol initialized
     
540. [    1.783436] Bluetooth: HCILL protocol initialized
     
541. [    1.789324] cpufreq version 1.0, suspend freq 1200 MHz
     
542. [    1.789906] cpuidle: using governor ladder
     
543. [    1.789952] cpuidle: using governor menu
     
544. [    1.790070] Synopsys Designware Multimedia Card Interface Driver
     
545. [    1.790900] dwmmc_rockchip ff0f0000.rksdmmc: Version ID is 270a
     
546. [    1.791772] dwmmc_rockchip ff0f0000.rksdmmc: Using internal DMA controller.
     
547. [    1.792273] 3230..dw_mci_init_slot: fmin=400000, fmax=100000000 [mmc0]
     
548. [    1.792329] Line3235..dw_mci_init_slot: The rk_sdmmc Ver 1.12 2014-07-08
     
549. [    1.792739] 1357..dw_mci_set_ios:  no card. [mmc0]
     
550. [    1.810037] 1357..dw_mci_set_ios:  no card. [mmc0]
     
551. [    1.829765] rk_sdmmc: BOOT dw_mci_setup_bus: argue clk_mmc workaround out 800000Hz for init[mmc0]
     
552. [    1.829797] dwmmc_rockchip ff0f0000.rksdmmc: DW MMC controller at irq 67, 32 bit host data width, 256 deep fifo
     
553. [    1.829822] dwmmc_rockchip ff0f0000.rksdmmc: 1 slots initialized
     
554. [    1.830184] dwmmc_rockchip ff0c0000.rksdmmc: Version ID is 270a
     
555. [    1.830950] dwmmc_rockchip ff0c0000.rksdmmc: Using internal DMA controller.
     
556. [    1.831134] 3224..dw_mci_init_slot: fmin=300000, fmax=50000000 [mmc1]
     
557. [    1.831666] 1357..dw_mci_set_ios:  no card. [mmc1]
     
558. [    1.849389] 1357..dw_mci_set_ios:  no card. [mmc1]
     
559. [    1.861880] mmc0: BKOPS_EN bit is not set
     
560. [    1.863798] rk_sdmmc: BOOT Bus speed=0Hz,Bus width=8bits.[mmc0]
     
561. [    1.866107] mmc_host mmc0: Bus speed (slot 0) = 100000000Hz (slot req 100000000Hz, actual 100000000HZ div = 0)
     
562. [    1.866135] rk_sdmmc: BOOT dw_mci_setup_bus: argue clk_mmc workaround out normal clock [mmc0]
     
563. [    1.869239] dwmmc_rockchip ff0c0000.rksdmmc: DW MMC controller at irq 64, 32 bit host data width, 256 deep fifo
     
564. [    1.869258] dwmmc_rockchip ff0c0000.rksdmmc: 1 slots initialized
     
565. [    1.869607] dwmmc_rockchip ff0d0000.rksdmmc: Version ID is 270a
     
566. [    1.869838] dwmmc_rockchip ff0d0000.rksdmmc: Using internal DMA controller.
     
567. [    1.869993] 3230..dw_mci_init_slot: fmin=200000, fmax=50000000 [mmc2]
     
568. [    1.870110] 1357..dw_mci_set_ios:  no card. [mmc2]
     
569. [    1.881165] rk_sdmmc: BOOT
     
570. [    1.881165]  execute tuning: candidates_degree = SDMMC_SHIFT_DEGREE_0        SDMMC_SHIFT_DEGREE_90   SDMMC_SHIFT_DEGREE_180  SDM]
     
571. [    1.881268] mmc0: new HS200 MMC card at address 0001
     
572. [    1.881527] mmcblk0: mmc0:0001 AWMB3R 14.5 GiB
     
573. [    1.881838]      uboot: 0x000400000 -- 0x000800000 (4 MB)
     
574. [    1.881851]       misc: 0x000800000 -- 0x000c00000 (4 MB)
     
575. [    1.881861]   resource: 0x000c00000 -- 0x001c00000 (16 MB)
     
576. [    1.881869]     kernel: 0x001c00000 -- 0x002c00000 (16 MB)
     
577. [    1.881878]       boot: 0x002c00000 -- 0x004c00000 (32 MB)
     
578. [    1.881887]   recovery: 0x004c00000 -- 0x006c00000 (32 MB)
     
579. [    1.881896]     backup: 0x006c00000 -- 0x00a000000 (52 MB)
     
580. [    1.881905]      cache: 0x00a000000 -- 0x012000000 (128 MB)
     
581. [    1.881914]     kpanic: 0x012000000 -- 0x012400000 (4 MB)
     
582. [    1.881923]     system: 0x012400000 -- 0x042400000 (768 MB)
     
583. [    1.881932]   metadata: 0x042400000 -- 0x042800000 (4 MB)
     
584. [    1.881941]   userdata: 0x042800000 -- 0x082800000 (1024 MB)
     
585. [    1.881950]  linuxroot: 0x082800000 -- 0x146800000 (3136 MB)
     
586. [    1.881959]       user: 0x146800000 -- 0x3a3a00000 (9682 MB)
     
587. [    1.881982]  mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p141357..dw_mci_set_ios:  no card. [mmc1]
     
588. [    1.888736] 1357..dw_mci_set_ios:  no card. [mmc2]
     
589. [    1.908414] 1357..dw_mci_set_ios:  no card. [mmc2]
     
590. [    1.908611] dwmmc_rockchip ff0d0000.rksdmmc: DW MMC controller at irq 65, 32 bit host data width, 256 deep fifo
     
591. [    1.908623] dwmmc_rockchip ff0d0000.rksdmmc: 1 slots initialized
     
592. [    1.908872] leds-gpio leds.31: pins are not configured from the driver
     
593. [    1.909099] hidraw: raw HID events driver (C) Jiri Kosina
     
594. [    1.910394] usbcore: registered new interface driver usbhid
     
595. [    1.910405] usbhid: USB HID core driver
     
596. [    1.910716] ashmem: initialized
     
597. [    1.910819] logger: created 256K log 'log_main'
     
598. [    1.910918] logger: created 256K log 'log_events'
     
599. [    1.911005] logger: created 256K log 'log_radio'
     
600. [    1.911096] logger: created 256K log 'log_system'
     
601. [    1.912100] input: rk29-keypad as /devices/ff100000.adc/key.34/input/input1
     
602. [    1.912674] rockchip-pinctrl ff770000.pinctrl: pin gpio6-8 already requested by smp; cannot claim for 2-0010
     
603. [    1.912690] rockchip-pinctrl ff770000.pinctrl: pin-200 (2-0010) status -22
     
604. [    1.912702] rockchip-pinctrl ff770000.pinctrl: could not request pin 200 on device rockchip-pinctrl
     
605. [    1.912714] ES8323 2-0010: Error applying setting, reverse things back
     
606. [    1.912999] es8323 probe i2c recv ok
     
607. [    1.913217] i2c-core: driver [ES8323] using legacy suspend method
     
608. [    1.913228] i2c-core: driver [ES8323] using legacy resume method
     
609. [    1.913552] rockchip-hdmi-spdif rockchip-hdmi-spdif.27: ASoC: CPU DAI (null) not registered
     
610. [    1.913583] rockchip_hdmi_spdif_audio_probe() register card failed:-517
     
611. [    1.913602] platform rockchip-hdmi-spdif.27: Driver rockchip-hdmi-spdif requests probe deferral
     
612. [    1.913828] es8323_probe
     
613. [    1.913913] es8323_probe:register ISR (irq=194)
     
614. [    2.548366] ES8323 2-0010: ASoC: no dapm match for LINPUT1 --> NULL --> Left Line Mux
     
615. [    2.548378] ES8323 2-0010: ASoC: Failed to add route LINPUT1 -> NULL -> Left Line Mux
     
616. [    2.548390] ES8323 2-0010: ASoC: no dapm match for LINPUT2 --> NULL --> Left Line Mux
     
617. [    2.548399] ES8323 2-0010: ASoC: Failed to add route LINPUT2 -> NULL -> Left Line Mux
     
618. [    2.548409] ES8323 2-0010: ASoC: no dapm match for Left PGA Mux --> NULL --> Left Line Mux
     
619. [    2.548418] ES8323 2-0010: ASoC: Failed to add route Left PGA Mux -> NULL -> Left Line Mux
     
620. [    2.548428] ES8323 2-0010: ASoC: no dapm match for RINPUT1 --> NULL --> Right Line Mux
     
621. [    2.548436] ES8323 2-0010: ASoC: Failed to add route RINPUT1 -> NULL -> Right Line Mux
     
622. [    2.548446] ES8323 2-0010: ASoC: no dapm match for RINPUT2 --> NULL --> Right Line Mux
     
623. [    2.548454] ES8323 2-0010: ASoC: Failed to add route RINPUT2 -> NULL -> Right Line Mux
     
624. [    2.548463] ES8323 2-0010: ASoC: no dapm match for Right PGA Mux --> NULL --> Right Line Mux
     
625. [    2.548472] ES8323 2-0010: ASoC: Failed to add route Right PGA Mux -> NULL -> Right Line Mux
     
626. [    2.548481] ES8323 2-0010: ASoC: no dapm match for LINPUT1 --> LAMP --> Left PGA Mux
     
627. [    2.548489] ES8323 2-0010: ASoC: Failed to add route LINPUT1 -> LAMP -> Left PGA Mux
     
628. [    2.548498] ES8323 2-0010: ASoC: no dapm match for LINPUT2 --> LAMP --> Left PGA Mux
     
629. [    2.548506] ES8323 2-0010: ASoC: Failed to add route LINPUT2 -> LAMP -> Left PGA Mux
     
630. [    2.548514] ES8323 2-0010: ASoC: no dapm match for Differential Mux --> LAMP --> Left PGA Mux
     
631. [    2.548523] ES8323 2-0010: ASoC: Failed to add route Differential Mux -> LAMP -> Left PGA Mux
     
632. [    2.548532] ES8323 2-0010: ASoC: no dapm match for RINPUT1 --> RAMP --> Right PGA Mux
     
633. [    2.548540] ES8323 2-0010: ASoC: Failed to add route RINPUT1 -> RAMP -> Right PGA Mux
     
634. [    2.548549] ES8323 2-0010: ASoC: no dapm match for RINPUT2 --> RAMP --> Right PGA Mux
     
635. [    2.548556] ES8323 2-0010: ASoC: Failed to add route RINPUT2 -> RAMP -> Right PGA Mux
     
636. [    2.548566] ES8323 2-0010: ASoC: no dapm match for Differential Mux --> RAMP --> Right PGA Mux
     
637. [    2.548574] ES8323 2-0010: ASoC: Failed to add route Differential Mux -> RAMP -> Right PGA Mux
     
638. [    2.548583] ES8323 2-0010: ASoC: no dapm match for LINPUT1 --> LAMP --> Differential Mux
     
639. [    2.548591] ES8323 2-0010: ASoC: Failed to add route LINPUT1 -> LAMP -> Differential Mux
     
640. [    2.548600] ES8323 2-0010: ASoC: no dapm match for RINPUT1 --> RAMP --> Differential Mux
     
641. [    2.548608] ES8323 2-0010: ASoC: Failed to add route RINPUT1 -> RAMP -> Differential Mux
     
642. [    2.548617] ES8323 2-0010: ASoC: no dapm match for LINPUT2 --> LAMP --> Differential Mux
     
643. [    2.548625] ES8323 2-0010: ASoC: Failed to add route LINPUT2 -> LAMP -> Differential Mux
     
644. [    2.548634] ES8323 2-0010: ASoC: no dapm match for RINPUT2 --> RAMP --> Differential Mux
     
645. [    2.548642] ES8323 2-0010: ASoC: Failed to add route RINPUT2 -> RAMP -> Differential Mux
     
646. [    2.548663] ES8323 2-0010: ASoC: no dapm match for LINPUT1 --> LAMP --> Left Line Mux
     
647. [    2.548671] ES8323 2-0010: ASoC: Failed to add route LINPUT1 -> LAMP -> Left Line Mux
     
648. [    2.548680] ES8323 2-0010: ASoC: no dapm match for LINPUT2 --> LAMP --> Left Line Mux
     
649. [    2.548688] ES8323 2-0010: ASoC: Failed to add route LINPUT2 -> LAMP -> Left Line Mux
     
650. [    2.548697] ES8323 2-0010: ASoC: no dapm match for Left PGA Mux --> LAMP --> Left Line Mux
     
651. [    2.548706] ES8323 2-0010: ASoC: Failed to add route Left PGA Mux -> LAMP -> Left Line Mux
     
652. [    2.548715] ES8323 2-0010: ASoC: no dapm match for RINPUT1 --> RAMP --> Right Line Mux
     
653. [    2.548724] ES8323 2-0010: ASoC: Failed to add route RINPUT1 -> RAMP -> Right Line Mux
     
654. [    2.548733] ES8323 2-0010: ASoC: no dapm match for RINPUT2 --> RAMP --> Right Line Mux
     
655. [    2.548741] ES8323 2-0010: ASoC: Failed to add route RINPUT2 -> RAMP -> Right Line Mux
     
656. [    2.548750] ES8323 2-0010: ASoC: no dapm match for Right PGA Mux --> RAMP --> Right Line Mux
     
657. [    2.548758] ES8323 2-0010: ASoC: Failed to add route Right PGA Mux -> RAMP -> Right Line Mux
     
658. [    2.548884] ES8323 2-0010: ASoC: mux Right Line Mux has no paths
     
659. [    2.548896] ES8323 2-0010: ASoC: mux Left Line Mux has no paths
     
660. [    2.548906] ES8323 2-0010: ASoC: mux Right PGA Mux has no paths
     
661. [    2.548915] ES8323 2-0010: ASoC: mux Left PGA Mux has no paths
     
662. [    2.548947] ES8323 2-0010: ASoC: mux Differential Mux has no paths
     
663. [    2.551789] Enter::rk29_es8323_init----135
     
664. [    2.555158] rockchip-es8323 rockchip-es8323.29:  ES8323 HiFirockchip-i2s.0 mapping ok
     
665. [    2.555657] u32 classifier
     
666. [    2.555665]     Actions configured
     
667. [    2.555676] Netfilter messages via NETLINK v0.30.
     
668. [    2.555727] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
     
669. [    2.556006] ctnetlink v0.93: registering with nfnetlink.
     
670. [    2.556069] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
     
671. [    2.556076] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
     
672. [    2.556303] xt_time: kernel timezone is -0000
     
673. [    2.556476] ip_tables: (C) 2000-2006 Netfilter Core Team
     
674. [    2.556590] arp_tables: (C) 2002 David S. Miller
     
675. [    2.556627] TCP: cubic registered
     
676. [    2.556635] Initializing XFRM netlink socket
     
677. [    2.556813] NET: Registered protocol family 10
     
678. [    2.557239] mip6: Mobile IPv6
     
679. [    2.557261] ip6_tables: (C) 2000-2006 Netfilter Core Team
     
680. [    2.557368] sit: IPv6 over IPv4 tunneling driver
     
681. [    2.557644] NET: Registered protocol family 17
     
682. [    2.557668] NET: Registered protocol family 15
     
683. [    2.557720] Bridge firewalling registered
     
684. [    2.557732] Ebtables v2.0 registered
     
685. [    2.557890] Bluetooth: RFCOMM TTY layer initialized
     
686. [    2.557920] Bluetooth: RFCOMM socket layer initialized
     
687. [    2.557927] Bluetooth: RFCOMM ver 1.11
     
688. [    2.557934] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
     
689. [    2.557939] Bluetooth: BNEP filters: protocol multicast
     
690. [    2.557949] Bluetooth: BNEP socket layer initialized
     
691. [    2.557956] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
     
692. [    2.557965] Bluetooth: HIDP socket layer initialized
     
693. [    2.557986] l2tp_core: L2TP core driver, V2.0
     
694. [    2.557998] l2tp_ppp: PPPoL2TP kernel driver, V2.0
     
695. [    2.558005] [WLAN_RFKILL]: Enter rfkill_wlan_init
     
696. [    2.558204] [WLAN_RFKILL]: Enter rfkill_wlan_probe
     
697. [    2.558213] wlan_platdata_parse_dt: wifi_chip_type = bcmwifi
     
698. [    2.558221] [WLAN_RFKILL]: wlan_platdata_parse_dt: enable wifi power control.
     
699. [    2.558229] [WLAN_RFKILL]: wlan_platdata_parse_dt: disable wifi io reference voltage control.
     
700. [    2.558237] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi power controled by gpio.
     
701. [    2.558258] [WLAN_RFKILL]: wlan_platdata_parse_dt: get property: WIFI,poweren_gpio = 156, flags = 0.
     
702. [    2.558276] [WLAN_RFKILL]: wlan_platdata_parse_dt: get property: WIFI,host_wake_irq = 158, flags = 0.
     
703. [    2.558284] [WLAN_RFKILL]: rfkill_wlan_probe: init gpio
     
704. [    2.558307] [WLAN_RFKILL]: rockchip_wifi_voltage_select: wifi & sdio reference voltage: 1.8V
     
705. [    2.558345] [WLAN_RFKILL]: Exit rfkill_wlan_probe
     
706. [    2.558388] [BT_RFKILL]: Enter rfkill_rk_init
     
707. [    2.558497] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: uart_rts_gpios = 147.
     
708. [    2.558512] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,power_gpio = 155.
     
709. [    2.558525] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,reset_gpio = 157.
     
710. [    2.558537] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_gpio = 154.
     
711. [    2.558550] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_host_irq = 159.
     
712. [    2.558595] [BT_RFKILL]: Request irq for bt wakeup host
     
713. [    2.558684] [BT_RFKILL]: ** disable irq
     
714. [    2.558757] [BT_RFKILL]: ap6335 device registered.
     
715. [    2.559366] rk3288-hdmi ff980000.hdmi: rk3288 hdmi probe sucess.
     
716. [    2.559759] VFP support v0.3: implementor 41 architecture 3 part 30 variant d rev 0
     
717. [    2.559779] rk3288_init_suspend
     
718. [    2.559787] rk3288_suspend_init enter
     
719. [    2.559908] rk3288_suspend_init: pm_ctrbits =40017
     
720. [    2.559938] gpio_get_dts_info suspend:8
     
721. [    2.559944] gpio_get_dts_info resume:8
     
722. [    2.559950] rockchip,pmic-suspend_gpios:1007c30 1007c40 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
     
723. [    2.559974] rockchip,pmic-resume_gpios:2007c32 2007c42 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
     
724. [    2.560091] clks_gating_suspend_init:clkgt info ok
     
725. [    2.560183] Registering SWP/SWPB emulation handler
     
726. [    2.560469] ddrfreq: verion 1.2 20140526
     
727. [    2.560480] ddrfreq: normal 456MHz video_1080p 0MHz video_4k 456MHz dualview 0MHz idle 0MHz suspend 200MHz reboot 456MHz
     
728. [    2.560489] ddrfreq: auto-freq=0
     
729. [    2.560494] ddrfreq: auto-freq-table[0] 240MHz
     
730. [    2.560500] ddrfreq: auto-freq-table[1] 324MHz
     
731. [    2.560505] ddrfreq: auto-freq-table[2] 456MHz
     
732. [    2.560510] ddrfreq: auto-freq-table[3] 528MHz
     
733. [    2.562091] act_ldo3: operation not allowed
     
734. [    2.562329] vga_edid_probe: turn on ldo3 done.
     
735. [    2.562353] act_ldo4: operation not allowed
     
736. [    2.562586] vga_edid_probe: turn on ldo done.
     
737. [    2.562606] act_ldo2: operation not allowed
     
738. [    2.562833] vga_edid_probe: turn on ldo2 done.
     
739. [    2.562854] act_ldo8: operation not allowed
     
740. [    2.563081] vga_edid_probe: turn on ldo done.
     
741. [    2.588168] vga-ddc: read and parse vga edid success.
     
742. [    2.588177] vga-ddc: max mode 1680x1050@59[pixclock-119005 KHZ]
     
743. [    2.588194] vga-ddc: best mode 1680x1050@60[pixclock-6 KHZ]
     
744. [    2.588200] vga_edid_probe: success. 9
     
745. [    2.588294] firefly_vga_get_enable 180, 0
     
746. [    2.588301] firefly_vga_get_status 186
     
747. [    2.588312] firefly_vga_set_enable 159 enable:1
     
748. [    2.588328] firefly_vga_enable 130 start
     
749. [    2.588335] firefly_switch_fb 55
     
750. [    2.588342]
     
751. [    2.588342] rk_fb_switch_screen lcdc_id 0 type 1 enable 1
     
752. [    2.588352] fb0 win id 1 state 1
     
753. [    2.588362] regulator-dummy: disabling
     
754. [    2.588386] rk3288-lcdc lcdc0: lcdc0: dclk:148500000>>fps:61
     
755. [    2.588407] fb1 win id 0 state 0
     
756. [    2.588413] fb2 win id 2 state 0
     
757. [    2.588418] fb3 win id 3 state 0
     
758. [    2.588424] fb4 win id 4 state 0
     
759. [    2.588429]
     
760. [    2.588429] rk_fb_switch_screen lcdc_id 0 type 1 enable 1 done
     
761. [    2.588429]
     
762. [    2.588459] VGA ENABLE
     
763. [    2.588719] rockchip-hdmi-spdif rockchip-hdmi-spdif.27: ASoC: CPU DAI (null) not registered
     
764. [    2.588744] rockchip_hdmi_spdif_audio_probe() register card failed:-517
     
765. [    2.588757] platform rockchip-hdmi-spdif.27: Driver rockchip-hdmi-spdif requests probe deferral
     
766. [    2.588832] pcd_pullup, is_on 0
     
767. [    2.588864] file system registered
     
768. [    2.589357] android_usb gadget: Mass Storage Function, version: 2009/09/11
     
769. [    2.589365] android_usb gadget: Number of LUNs=2
     
770. [    2.589372]  lun0: LUN: removable file: (no medium)
     
771. [    2.589379]  lun1: LUN: removable file: (no medium)
     
772. [    2.589495] android_usb gadget: android_usb ready
     
773. [    2.589569] sensor_init: Probe name sensors
     
774. [    2.589583] sensor-dev.c v1.4 add angle calculation support between two gsensors 2013-09-01
     
775. [    2.590104] rtc_hym8563 0-0051: setting system clock to 2014-12-26 20:16:49 UTC (1419625009)
     
776. [    2.595336] usbcore: registered new interface driver snd-usb-audio
     
777. [    2.595362] ALSA device list:
     
778. [    2.595368]   #0: RK_ES8323
     
779. [    2.596651] Freeing unused kernel memory: 2368K (c0a3c000 - c0c8c000)
     
780. [    2.596907] rockchip-hdmi-spdif rockchip-hdmi-spdif.27:  rk-hdmi-spdif-hifirockchip-spdif mapping ok
     
781. [    2.601414] SELinux:  Permission attach_queue in class tun_socket not defined in policy.
     
782. [    2.601427] SELinux: the above unknown classes and permissions will be denied
     
783. [    2.826458] type=1403 audit(1419625009.730:2): policy loaded auid=4294967295 ses=4294967295
     
784. [    2.826553] SELinux: Loaded policy from /sepolicy
     
785. [    2.827969] type=1404 audit(1419625009.730:3): enforcing=1 old_enforcing=0 auid=4294967295 ses=4294967295
     
786. [    3.204881] vga-ddc: read and parse vga edid success.
     
787. [    3.204894] vga-ddc: max mode 1680x1050@59[pixclock-119005 KHZ]
     
788. [    3.204910] vga-ddc: best mode 1680x1050@60[pixclock-6 KHZ]
     
789. [    3.204916] VGA Devie connected 9
     
790. [    3.204921] firefly_vga_set_mode 203
     
791. [    3.204927] firefly_vga_set_mode 219 1680 1050 60 146200000
     
792. [    3.204933] firefly_vga_enable 130 start
     
793. [    3.204938] firefly_switch_fb 55
     
794. [    3.204945]
     
795. [    3.204945] rk_fb_switch_screen lcdc_id 0 type 1 enable 1
     
796. [    3.204955] fb0 win id 1 state 1
     
797. [    3.204997] rk3288-lcdc lcdc0: lcdc0: dclk:148500000>>fps:61
     
798. [    3.205019] fb1 win id 0 state 0
     
799. [    3.205024] fb2 win id 2 state 0
     
800. [    3.205030] fb3 win id 3 state 0
     
801. [    3.205035] fb4 win id 4 state 0
     
802. [    3.205040]
     
803. [    3.205040] rk_fb_switch_screen lcdc_id 0 type 1 enable 1 done
     
804. [    3.205040]
     
805. [    3.728799] dwc_otg_hcd_enable, enable host controller
     
806. [    3.832476] Using Buffer DMA mode
     
807. [    3.832486] Periodic Transfer Interrupt Enhancement - disabled
     
808. [    3.832493] Multiprocessor Interrupt Enhancement - disabled
     
809. [    3.832499] OTG VER PARAM: 0, OTG VER FLAG: 0
     
810. [    3.832505] ^^^^^^^^^^^^^^^^^^Host Mode
     
811. [    3.847006] init: init.rk30board.bootmode.emmc.rc: 8: invalid command '/devices/ff0f0000.rksdmmc/mmc_host/mmc'
     
812. [    3.847025] init: init.rk30board.bootmode.emmc.rc: 9: invalid command '/devices/ff0c0000.rksdmmc/mmc_host/mmc'
     
813. [    3.847038] init: init.rk30board.bootmode.emmc.rc: 10: invalid command '/devices/ff580000.usb'
     
814. [    3.847048] init: init.rk30board.bootmode.emmc.rc: 11: invalid command '/devices/ff580000.usb'
     
815. [    3.847058] init: init.rk30board.bootmode.emmc.rc: 12: invalid command '/devices/ff500000.usb'
     
816. [    3.847068] init: init.rk30board.bootmode.emmc.rc: 13: invalid command '/devices/ff500000.usb'
     
817. [    3.847077] init: init.rk30board.bootmode.emmc.rc: 14: invalid command '/devices/ff540000.usb'
     
818. [    3.847087] init: init.rk30board.bootmode.emmc.rc: 15: invalid command '/devices/ff540000.usb'
     
819. [    3.847376] init (1): /proc/1/oom_adj is deprecated, please use /proc/1/oom_score_adj instead.
     
820. [    3.876492] Init: Power Port (0)
     
821. [    3.907716] init: /dev/hw_random not found
     
822. [    3.907773] keychord: using input dev ff680000.pwm for fevent
     
823. [    3.907782] keychord: using input dev rk29-keypad for fevent
     
824. [    3.907936] init: cannot open '/initlogo.rle'
     
825. [    3.920169] fs_mgr: parse_link_device : path = NULL
     
826. [    3.920192] fs_mgr: parse_link_device : path = NULL
     
827. [    3.920209] fs_mgr: parse_link_device : path = NULL
     
828. [    3.920225] fs_mgr: parse_link_device : path = NULL
     
829. [    3.920241] fs_mgr: parse_link_device : path = NULL
     
830. [    3.920257] fs_mgr: parse_link_device : path = NULL
     
831. [    3.920273] fs_mgr: parse_link_device : path = NULL
     
832. [    3.920288] fs_mgr: parse_link_device : path = NULL
     
833. [    3.920343] fs_mgr: ---------------resize_fs blk_dev /dev/block/platform/ff0f0000.rksdmmc/by-name/system, type ext4fs_mgr: Runnim
     
834. [    3.921113] resize2fs: resize2fs 1.41.14 (22-Dec-2010)resize2fs: The filesystem is already 196608 blocks long.  Nothing to do!re
     
835. [    3.927764] EXT4-fs (mmcblk0p10): mounted filesystem with ordered data mode. Opts: noauto_da_alloc
     
836. [    3.941577] EXT4-fs (mmcblk0p8): recovery complete
     
837. [    3.945343] EXT4-fs (mmcblk0p8): mounted filesystem with ordered data mode. Opts: noauto_da_alloc,discard
     
838. [    3.947457] EXT4-fs (mmcblk0p11): recovery complete
     
839. [    3.947469] EXT4-fs (mmcblk0p11): mounted filesystem with ordered data mode. Opts: noauto_da_alloc,discard
     
840. [    3.955089] EXT4-fs (mmcblk0p12): recovery complete
     
841. [    3.955665] EXT4-fs (mmcblk0p12): mounted filesystem with ordered data mode. Opts: noauto_da_alloc,discard
     
842. [    3.960589] drmboot: version magic '3.0.36+ SMP preempt mod_unload ARMv7 ' should be '3.10.0 SMP preempt mod_unload ARMv7 p2v8 '
     
843. [    3.965686] mali pd enabled
     
844. [    3.965699] clk enabled
     
845. [    3.965708] MALI_DVFS_STEP=4,div_dvfs=10
     
846. [    3.965715] mali_dvfs_infotbl[0].clock=198000,min_threshold=0,max_threshold=70
     
847. [    3.965722] mali_dvfs_infotbl[1].clock=297000,min_threshold=70,max_threshold=80
     
848. [    3.965729] mali_dvfs_infotbl[2].clock=417000,min_threshold=80,max_threshold=90
     
849. [    3.965736] mali_dvfs_infotbl[3].clock=480000,min_threshold=94,max_threshold=100
     
850. [    3.966851] turn on mali power
     
851. [    3.966875] mali ffa30000.gpu: GPU identified as 0x0750 r0p0 status 1
     
852. [    3.967241] mali ffa30000.gpu: Probed as mali0
     
853. [    4.191280] Indeed it is in host mode hprt0 = 00021501
     
854. [    4.368390] usb 3-1: new high-speed USB device number 2 using usb20_host
     
855. [    4.368454] Indeed it is in host mode hprt0 = 00001101
     
856. [    4.565389] usb 3-1: New USB device found, idVendor=1a40, idProduct=0101
     
857. [    4.565400] usb 3-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
     
858. [    4.565408] usb 3-1: Product: USB 2.0 Hub [MTT]
     
859. [    4.565711] hub 3-1:1.0: USB hub found
     
860. [    4.565765] hub 3-1:1.0: 4 ports detected
     
861. [    4.840799] usb 3-1.1: new full-speed USB device number 3 using usb20_host
     
862. [    4.940291] usb 3-1.1: New USB device found, idVendor=058f, idProduct=9254
     
863. [    4.940305] usb 3-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
     
864. [    4.940313] usb 3-1.1: Product: Generic USB Hub
     
865. [    4.940319] usb 3-1.1: Manufacturer: ALCOR
     
866. [    4.940661] hub 3-1.1:1.0: USB hub found
     
867. [    4.940909] hub 3-1.1:1.0: 4 ports detected
     
868. [    5.214718] usb 3-1.1.3: new low-speed USB device number 4 using usb20_host
     
869. [    5.319076] usb 3-1.1.3: New USB device found, idVendor=413c, idProduct=3016
     
870. [    5.319090] usb 3-1.1.3: New USB device strings: Mfr=0, Product=2, SerialNumber=0
     
871. [    5.319098] usb 3-1.1.3: Product: Dell Premium USB Optical Mouse
     
872. [    5.324981] input: Dell Premium USB Optical Mouse as /devices/ff540000.usb/usb3/3-1/3-1.1/3-1.1.3/3-1.1.3:1.0/input/input2
     
873. [    5.325451] hid-generic 0003:413C:3016.0001: input,hidraw0: USB HID v1.11 Mouse [Dell Premium USB Optical Mouse] on usb-ff5400000
     
874. [    5.401728] usb 3-1.1.4: new low-speed USB device number 5 using usb20_host
     
875. [    5.507779] usb 3-1.1.4: New USB device found, idVendor=413c, idProduct=2107
     
876. [    5.507793] usb 3-1.1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
     
877. [    5.507801] usb 3-1.1.4: Product: Dell USB Entry Keyboard
     
878. [    5.507808] usb 3-1.1.4: Manufacturer: Dell
     
879. [    5.512370] input: Dell Dell USB Entry Keyboard as /devices/ff540000.usb/usb3/3-1/3-1.1/3-1.1.4/3-1.1.4:1.0/input/input3
     
880. [    5.512512] keychord: using input dev Dell Dell USB Entry Keyboard for fevent
     
881. [    5.512840] hid-generic 0003:413C:2107.0002: input,hidraw1: USB HID v1.10 Keyboard [Dell Dell USB Entry Keyboard] on usb-ff540000
     
882. [    5.598384] iep dpi mode inactivity
     
883. [    9.800881] es8323_mic_state_ctrl read: 0
     
884. [    9.800892] mic_state_switch 0
     
885. [    9.800898] hp_det = 0,insert hp
     
886. [    9.800903] hp mic use intern
     
887. [   17.514622] *****************vbus detect*******************

Copy the code

e97

Hi, I too have been unable to create an image from the released SDK.




The only method where I have successfully booted the device is:




1) Flash with the factory Android 4.4 image, 'Firefly-RK3288_Android4.4_201412111722.img'

2) Overwrite 'system.img' with your 'system.img' image




Replacing kernel.img with one generated from the SDK locks up on the Firefly logo screen on bootup.




Replacing boot.img with one generated from the SDK is OK.




I'm also unsure which bootloader, uboot images are used in the factory image. Knowing this would be helpful.

isle

you can unpack the factory image by? Firmware Upgrade Tool for Windows which you can get from our website
http://www.t-firefly.com/en/download/


?

then, follow these steps:

1. edit the file: AndroidTool_Release_v2.3/config.ini ,change Selected=1 to 2;

2. execute the AndroidTool.exe

3. find the Advanced Function , then you will find the fireware unpack function.

finally， you will get all the image file from Output folder.




Have? fun !

e97

Thank you isle. That was very helpful!




I think my issue is I compiled the kernel incorrectly with the linaro cross compile toolchain. I've used it successfully for other Android builds, I'm not sure why it does not work here... maybe answers to the the following will explain why... [SOLVED]




On Ubuntu 12.04, when running:




make ARCH=arm CROSS_COMPILE=CROSS_COMPILE=arm-linux-gnueabihf- firefly-rk3288_defconfig
make ARCH=arm CROSS_COMPILE=CROSS_COMPILE=arm-linux-gnueabihf- -j8 firefly-rk3288.img







Results in a linking error:

make[1]: *** [pie/pie_stage3.o] Error 1


However, if the ARCH and CROSS_COMPILE are not specified:







make firefly-rk3288_defconfig
make -j8 firefly-rk3288.img




It works OK. Why is this??




------------




Update:?https://plus.google.com/u/0/110719562692786994119/posts/MyGmGKPY4jF




Answers a lot of questions: Rockchip method specifies a CROSS_COMPILE toolchain inside the Makefile

isle

I think your specified CROSS_COMPILE is not right .




when you have no specified CROSS_COMPILE.

it use the default .

see Makefile in kernel folder.

the CROSS_COMPILE tools is here:

../prebuilts/gcc/linux-x86/arm/