Open the auxiliary access

Firefly Open Source Community

   Login   |   Register   |
New_Topic
Firefly Open Source Community › Core Board › Core-3308Y› FCSS_LED_AR-7.6ウェブトレーニング、FCSS_LED_AR-7.6模 ...
New Topic
Print Previous Topic Next Topic

[General] FCSS_LED_AR-7.6ウェブトレーニング、FCSS_LED_AR-7.6模擬対策

liamste188

134

Credits

0

Prestige

0

Contribution

registered members

Rank: 2

Credits
134

【General】 FCSS_LED_AR-7.6ウェブトレーニング、FCSS_LED_AR-7.6模擬対策

Posted at yesterday 23:50      View：10 | Replies：0        Print      Only Author   [Copy Link] 1#
P.S. PassTestがGoogle Driveで共有している無料かつ新しいFCSS_LED_AR-7.6ダンプ：https://drive.google.com/open?id=1SC1AXI8OVfob5woQAZxEDTRmmaXi8ncW
認めなければならないことは、あなたが所有する認定資格がますます増えていることです。 これが、FCSS_LED_AR-7.6認定を取得することの重要性を認識する必要がある理由です。 私たちの将来の雇用のためのより資格のある認定は、彼らの能力を証明するのに十分な資格認定を持っているだけで、社会的競争でライバルに勝つことができると見なされる効果があります。 したがって、FCSS_LED_AR-7.6ガイド急流は、ユーザーがより速く、より効率的に参加するために必要な資格のあるFCSS_LED_AR-7.6試験に合格するのに役立ちます。
Fortinet FCSS_LED_AR-7.6 認定試験の出題範囲：
トピック出題範囲
トピック 1
  • Monitoring and Troubleshooting: This section covers configuring quarantine mechanisms, managing FortiAIOps, troubleshooting FortiGate communication with FortiSwitch and FortiAP, and using monitoring tools for wireless connectivity.
トピック 2
  • Authentication: This domain covers advanced user authentication using RADIUS and LDAP, two-factor authentication with digital certificates, and configuring syslog and RADIUS single sign-on on FortiAuthenticator.
トピック 3
  • Zero-Trust LAN Access: This domain covers machine authentication, MAC Authentication Bypass, NAC policies for wireless security, guest portal deployment, and advanced solutions like FortiLink NAC, dynamic VLAN, and VLAN pooling.
トピック 4
  • Central Management: This section addresses managing FortiSwitch via FortiManager over FortiLink, implementing zero-touch provisioning, configuring VLANs, ports, and trunks, and setting up FortiExtender and FortiAP devices.

FCSS_LED_AR-7.6模擬対策 & FCSS_LED_AR-7.6テスト資料もしFCSS_LED_AR-7.6認定試験を受験したいなら、FCSS_LED_AR-7.6試験参考書が必要でしょう。ターゲットがなくてあちこち参考資料を探すのをやめてください。どんな資料を利用すべきなのかがわからないとしたら、PassTestのFCSS_LED_AR-7.6問題集を利用してみましょう。この問題集は的中率が高くて、あなたの一発成功を保証できますから。ほかの試験参考書より、この問題集はもっと正確に実際問題の範囲を絞ることができます。こうすれば、この問題集を利用して、あなたは勉強の効率を向上させ、十分にFCSS_LED_AR-7.6試験に準備することができます。
Fortinet FCSS - LAN Edge 7.6 Architect 認定 FCSS_LED_AR-7.6 試験問題 (Q59-Q64):質問 # 59
Which policy components are essential in a FortiGate NAC policy for wireless networks?
(Choose three)
Response:
  • A. Authentication rules
  • B. IPsec VPN enforcement
  • C. VLAN assignment
  • D. Role assignment
  • E. Posture check condition
正解：A、C、D

質問 # 60
Refer to the exhibits.



A company has multiple FortiGate devices deployed and wants to centralize user authentication and authorization. The administrator decides to use FortiAuthenticator to convert RSSO messages to FSSO, allowing all FortiGate devices to receive user authentication updates.
After configuring FortiAuthenticator to receive RADIUS accounting messages, users can authenticate, but FortiGate does not enforce the correct policies based on user groups. Upon investigation, the administrator discovers that FortiAuthenticator is receiving RADIUS accounting messages from the RADIUS server and successfully queries LDAP for user group information. But, FSSO updates are not being sent to FortiGate devices and FortiGate firewall policies based on FSSO user groups are not being applied.
What is the most likely reason FortiGate is not receiving FSSO updates?
  • A. The LDAP server is not configured to retrieve group memberships for RSSO users.
  • B. FortiAuthenticator is missing the FSSO user group attribute in the configuration.
  • C. The FortiAuthenticator interface is not enabled to receive RADIUS accounting messages.
  • D. The RADIUS Username and Client IPv4 attributes are not defined on FortiAuthenticator.
正解：D
解説：
In this design, FortiAuthenticator receivesRADIUS accounting (RSSO) messages, looks up the user in LDAP to get group information, theninjects FSSO logon eventstoward all FortiGate devices.
From the exhibits we know:
* FortiAuthenticatoris receiving RADIUS accountingfrom the RADIUS server.
* LDAP queries are successful and return group membership.
* But FortiGatedoes not receive FSSO logons, so identity-based policies are not applied.
For FortiAuthenticator to create an FSSO logon, the RADIUS accounting record must be correctlyparsed into at least:
* Username
* Client IP address
These are mapped from the RADIUS attributes in theRADIUS Accounting SSO clientconfiguration (for example, User-Name and Framed-IP-Address). If these are not defined or mapped incorrectly, FortiAuthenticator can see the accounting packet butcannot build a valid FSSO session, so no update is sent to FortiGate.
Thus the most likely root cause is:
#The RADIUS Username and Client IPv4 attributes are not correctly definedfor that RADIUS Accounting SSO client (optionA).
Other options conflict with the scenario:
* B- LDAP is already successfully returning groups.
* C- FSSO user group attribute is separate; even without it, FSSO logons would still be created (just without group mapping).
* D- The interfaceisreceiving RADIUS accounting, so it is clearly enabled.

質問 # 61
Refer to the exhibits.


A set of SSID profiles has been configured on FortiManager, and an AP profile has been assigned to a group of AP managed by FortiGate. However, none of the designated SSIDs are being broadcast by these APs.
Which configuration change is required to make the APs broadcast these SSIDs as intended?
  • A. Change the AP profile to use a platform that supports the configured mix of SSIDs.
  • B. Set the Transmit Power Mode to Auto.
  • C. Choose Manual in the SSIDs setting and select the SSIDs to broadcast.
  • D. Adjust the AP profile to ensure all SSIDs are configured in a supported mode, either bridge or tunnel, but not a mix of both.
正解：C
解説：
From the exhibits:
* The AP profile shows:
* SSIDs: Tunnel | Bridge | Manual
* The current setting isBridge, not Manual.
* WhenBridgeorTunnelis selected, the AP profiledoes NOT automatically broadcast SSIDsunless the corresponding VAPs were explicitly mapped in the AP profile.
* FortiManager SSID profiles are created, but unless these are explicitly applied underManual SSIDs selection, the AP will not broadcast any SSID.
Fortinet documentation states:
"To control which SSIDs an AP broadcasts, the AP Profile must have SSIDs set toManual, and the desired SSIDs must be selected." Therefore, to make the AP broadcast the intended SSIDs:
#You must switch the SSIDs setting to Manual, and manually select the SSIDs (CompanyPrinters, Student01, Guest-CorpPort, PSK).
Why the other options are incorrect:
* A. Adjust AP profile to avoid mixing bridge/tunnelMixed modes ARE supported. Not the issue.
* B. Change platformThe platform (FAP231F) already supports all listed SSIDs.
* D. Set transmit power mode to autoPower settings have nothing to do with SSID broadcasting.

質問 # 62
Which three FortiAuthenticator configuration elements are involved in RSSO processing?
(Choose three)
Response:
  • A. Syslog Server
  • B. RSSO Attribute
  • C. RADIUS Client
  • D. Group Mapping
  • E. DNS Filter
正解：B、C、D

質問 # 63
APs have been manually configured to connect to FortiGate over an IPsec network, and FortiGate successfully detects and authorizes them. However, the APs remain unmanaged because FortiGate is unable to establish a CAPWAP tunnel with them.
What configuration change can resolve this issue and enable FortiGate to establish the CAPWAP tunnel over the IPsec connection?
  • A. Assign a custom AP profile for the remote APs with the set mpls-connection option enabled.
  • B. Configure a static route on FortiGate to reach the APs over the IPsec tunnel.
  • C. Decrease the CAPWAP tunnel MTU size for APs to prevent fragmentation.
  • D. Upgrade the FortiAP firmware image to ensure compatibility with the FortiOS version.
正解：A
解説：
When FortiAPs connect to FortiGate overIPsec tunnels, this is treated similarly to WAN/MPLS deployments.
In these scenarios, FortiGate must know that CAPWAP must traverse anon-L2transport.
FortiAP profiles include:
set mpls-connection enable
This setting is required so that:
* FortiGate can encapsulate CAPWAP inside the transport tunnel
* Remote FortiAPs can establish CAPWAP even when behind routed/IPsec networks Without this option, the FortiGate detects the AP butcannot bring CAPWAP UP, leaving the AP in
"discovered/unauthorized" or "offline" state.
Why others are wrong
* A. Static route# Discovery already succeeds, so routing is not the issue.
* C. Reduce MTU# Sometimes useful for IPsec, but not required for CAPWAP establishment.
* D. Firmware upgrade# Firmware mismatch would show "Managed (upgrade required)," not CAPWAP tunnel failure.
Therefore,set mpls-connection enableis the required fix.

質問 # 64
......
FortinetのFCSS_LED_AR-7.6スタディガイドは無料のトライアルサービスを提供するため、スタディの内容、トピック、購入前にソフトウェアを最大限に活用する方法についての情報を得ることができます。 どのようなFCSS_LED_AR-7.6テスト準備が適切であるかを選択し、不必要な無駄を避けるために適切な選択をするのに良い方法です。 また、PassTestのFCSS_LED_AR-7.6練習用トレントまたはトレイルプロセスの購入で問題が発生した場合は、すぐにご連絡いただければ、専門家によるFCSS_LED_AR-7.6のFCSS - LAN Edge 7.6 Architect学習教材のオンラインサポートを提供します。
FCSS_LED_AR-7.6模擬対策: https://www.passtest.jp/Fortinet/FCSS_LED_AR-7.6-shiken.html
ちなみに、PassTest FCSS_LED_AR-7.6の一部をクラウドストレージからダウンロードできます：https://drive.google.com/open?id=1SC1AXI8OVfob5woQAZxEDTRmmaXi8ncW
https://www.briandumpsprep.com
Reply

Use props Report

Return to List
High mode
B Color Image Link Quote Code Smilies
You need to log in before you can reply Login | Register

This forum Credits Rules

  •  

Service Hotline : (+86)18688117175
Contact us
E-mail : global@t-firefly.com
Copyright © 2014-2022, FIREFLY TECHNOLOGY CO.,LTD. All Rightts Reserved. 粤ICP备14022046号-2
Quick Reply Back to top Back to list